2021/04/07
Can They Be Better?
By Tony Haddrell, Marino Phocas, and Nico Ricquier
We examine the antenna designs that provide GPS functionality to mobile phones and why most phones still do not provide GPS operation indoors. We also see what it will take to make them better.
INNOVATION INSIGHTS by Richard Langley
WHAT ARE THREE THINGS THAT MATTER MOST for a good GPS signal? Antenna, antenna, antenna. The familiar real-estate adage can be rephrased for this purpose, although the original — location, location, location — is valid here, too.
GPS satellite signals are notoriously weak compared to familiar terrestrial signals such as those of broadcast stations or mobile-phone towers. However, if an appropriate antenna has a clear line-of-sight to the satellite, excellent receiver performance is the norm. But what constitutes an appropriate antenna? The GPS signals are right-hand circularly polarized (RHCP) to provide fade-free reception as the satellite’s orientation changes during a pass. A receiving antenna with matching polarization will transfer the most signal power to the receiver. Microstrip patch antennas and quadrifilar helices, two RHCP antennas commonly used for GPS reception, have omnidirectional (in azimuth) gain patterns with typical unamplified boresight gains of a few dB greater than that of an ideal isotropic RHCP antenna.
But what happens when signals are obstructed by trees or buildings or, worse yet, when we move indoors? Received signal strength plummets. A conventional receiver, even with a good antenna, will then have difficulty acquiring and tracking the signals, resulting in missed or even no position fixes. However, thanks in large part to massive parallel correlation, receivers have been developed with 1,000 times more sensitivity than conventional receivers, permitting operation in restricted environments, albeit usually with reduced positioning accuracy. But such operation requires a standard antenna.
So, do the GPS receivers in our mobile phones now work everywhere? Sadly, no. Consumers demand that their phones not only provide voice communications and GPS but also Bluetooth connectivity to headsets, Wi-Fi, and even an FM transmitter, all in a small form factor at reasonable cost. This requires miniaturizing the GPS antenna and possibly integrating it with the other radio services on the platform. Such compromises can, if the designer is not careful, significantly reduce receiver effectiveness with dramatically reduced antenna gain and distorted antenna patterns. This month we look at some antenna designs providing GPS functionality to mobile phones and examine why most phones still do not provide GPS operation indoors or in other challenging environments. We also find out what it will take to make them better.
“Innovation” is a regular column that features discussions about recent advances in GPS technology and its applications as well as the fundamentals of GPS positioning. The column is coordinated by Richard Langley of the Department of Geodesy and Geomatics Engineering at the University of New Brunswick, who welcomes your comments and topic ideas.
GPS is becoming a must-have feature in mobile phones, with major manufacturers launching new designs regularly, and second-tier manufacturers rapidly catching up. A quick test of any early GPS-equipped phone shows that although the incumbent GPS chip (or chipset) has high sensitivity, the integrated end result cannot perform in low signal conditions. Several challenges facing the phone designer are responsible for this, with the main two being the antenna performance and interference in the GPS band generated within the phone platform itself.
Here we explore the antenna’s role in determining overall performance of the GPS function in a mobile phone, and the potential for avoiding some platform jamming signals by choice of antenna technology.We present some results from an ongoing company study, as part of our remit to assist customers at the system integration level in support of GPS chip sales.
Many handset makers are not GPS or even RF experts, and rely on catalog components to provide their GPS and antenna hardware. Often unsuitable antennas are chosen, or the antennas are integrated in such a way that the original operation mode does not work. Study of a number of candidate phones has shown that, due to the small ground plane available, the antenna component may be merely a band-tuning device, with the ground plane contributing the signal collection function.
At the beginning of 2008, our team launched a project to understand and prioritize the problems for handset makers in the antenna area, and to provide better solutions than those currently in use.
The handset designer faces several problems when incorporating a GPS antenna. First, it has to be very low cost (a few cents, probably). Secondly, it has to be broadly omnidirectional, since there is no knowledge of “up” on a mobile phone, although some manufacturers rely on the fact that location will only be needed when the phone is in the user’s hand or an in-car holder. From the GPS receiver point of view, we would like the antenna to be as far from the communications (transmitting) antenna as possible, and also removed from other transmitting services such as Bluetooth, Wi-Fi, and FM. Users must not be able to detune the antenna out of band by placing their hands on the phone, or by raising the phone to their ears. In a perfect world, they would not obscure an antenna either.
Of course, we would also like to remove some of that platform interference at the antenna stage, and techniques such as differential RF inputs (with a differential antenna) have been proposed in the search for better noise-cancellation performance.
All of this leaves the handset designer with an impossible task, since he has run out of space to fit a decent GPS antenna with all the isolation requirements, and we typically measure GPS antennas that average 26 to 215 dB of gain with respect to a reference dipole, which measures around 21 dB compared to an isotropic antenna when integrated in the handset. Given that a 2 dB loss equates to double the time to fix (in low signal environments) or, alternately, double the amount of baseband signal-search hardware in the GPS chip, it follows that we must exert some effort to help handset integrators implement better antennas. In this respect, some larger manufacturers have in-house projects running, but smaller ones do not have antenna design teams and rely on their suppliers to provide solutions.
So, we start with cataloging the requirements, and given that most current implementations are only in the “mediocre to terrible” class, we look at ways of improving things accordingly. Of course, there are good GPS antenna solutions out there, but handset designers have mostly shunned them on the grounds of cost or even size. Restrictions on these parameters severely hamper the antenna designer, as reducing a GPS L1 antenna below its “natural” size — about 4 centimeters for a monopole on commonly used FR4-type printed circuit board (PCB) material — inevitably means either using some higher dielectric material, which adds cost, or folding the structure up, which decreases performance.
Single-ended antennas, such as monopoles and microstrip patches, rely on a ground plane, which in a handset is undersized anyway, and is usually difficult to identify and model. True differential designs (such as a dipole) overcome this problem, but are automatically larger. As handsets get smaller and encompass more “connectivity”
(that is, more radio links, including GPS) and competition for antenna space increases, combined antennas become attractive, as they would at least help with the size issue. However, the isolation problems are increased, and since our various radios all (currently) need individual RF inputs, some new layer of complexity and filtering is needed between antenna and chip.
Theory, Performance. We undertook some practical experiments to get a feel for the gap between an antenna’s theoretical performance and its installed performance when integrated with the other phone functions. At present, the idea of modeling all the radiation interactions and mechanical arrangements within such a platform is beyond the scope of the available tools, and so practical measurements are really our only choice in the quest for better antennas.
Finally, we provide some insight into the future, given the rapid advancements driven by mobile-phone technology and the advent of the low-cost handset for new emerging markets. New challenges loom ahead for GNSS antennas, not the least being more bandwidth and multiple frequencies, and we look briefly at what must be done to keep up with handset manufacturers’ requirements in this regard.
Size of the Problem
Location-based services in mobile phones is now an expected function by the more discerning user. With more than 500 million users of such services expected by 2011, pressure on manufacturers to provide ever better user experiences and competition between phone manufacturers will bring pressure on the GPS industry for improved performance. GNSS is now the location technology of choice for mobile phones and will remain so provided that the industry can maintain leadership in cost, size, and performance. FIGURE 1 shows the expected penetration of GNSS (mostly just GPS) in the next few years.
Figure 1. GNSS penetration, mobile phones (Image: Tony Haddrell, Marino Phocas, and Nico Ricquier)
With this many users, the market will soon decide whether the performance is up to expectation or not; this in itself will determine GPS penetration going forward.
Vanishing Space. The first challenge facing the RF antenna designer working on a mobile phone is the size of the whole platform. As the size of the average phone continues to fall, manufacturers are understandably reluctant to increase size again to add new features, such as GPS. Consider the wavelengths of a phone’s various RF services. If the corresponding antennas were implemented as dipoles, the antennas would be bigger than the phone. Clearly the competition for antenna space is high. The designer will want to separate the antennas as much as possible to reduce coupling between them, both in the sense of coupling interference from one service to another (known as isolation) and in the sense of spoiling the pattern (or field) of one antenna with another (interaction).
The chip business addresses the space issue through the advent of combination or combo chips, containing such peripheral services as FM (both receive and transmit), Bluetooth, GPS, and Wi-Fi. While helping with space constraints, this development brings new challenges as these radios have to cohabit the same silicon and still perform individually, whatever the other radios are doing (transmitting music to the car radio using FM while navigating with GPS, for example). It follows that combo antennas similarly save space, but since this might involve simultaneous transmit and GPS receive functions, it is very difficult to achieve the necessary isolation, especially if the user’s body can change the coupling between functions.
FIGURE 2 shows a modern phone with some antennas identified. Not shown is the FM transmit antenna on the rear (the receive function uses the headset cable). One commercially available combo antenna and two custom-made antennas are designed to fit the mechanical layout of the phone. The GPS antenna has been placed at the top of the phone, relegating the communications antenna (really another combo since it handles four frequency bands) to the bottom of the phone, where it is subject to detuning by the user’s hand. The GPS antenna is of the PIFA (planar inverted F antenna) type, working against the ground plane of the main PCB, and is printed on a plastic molding that also implements a loudspeaker and its electrical connections.
Figure 2. Antennas in a mobile phone: 1. GSM/WCDMA antenna, 2.Wi-Fi/Bluetooth combined ceramic chip antenna, 3. GPS antenna (Image: Tony Haddrell, Marino Phocas, and Nico Ricquier)
Size. Until now, we have not looked at the size of GPS antennas. We know that a dipole (on FR4 PCB material) is about 8 centimeters in length, just a little shorter than the average phone platform. Changing to a monopole halves the natural length, but requires an “infinite” ground plane to work against. Ignoring this requirement, some manufacturers simply print a monopole on the main PCB, and put up with the coupling, losses, and pattern deficiencies that arise. Some while ago, we measured the gain of such an arrangement at about 212 dB relative to the reference dipole. So designers have turned to size-reduced antennas, either by using higher dielectric materials to form them, or by using complex shape and feed derivatives (such as the PIFA in Figure 2.)
Another combo idea is to use the communications antenna. In the case shown in FIGURE 3, this is a whip-type antenna on a clamshell-type phone. Although the antenna is free for GPS and uses no additional space, the components to tune the whip for GPS and prevent the transmit bands reaching the GPS low noise amplifier (LNA) add both cost and size. So this is not really too attractive, especially when measurements show a 216 dB performance relative to our dipole, along with a poor coverage pattern. In this model, removing the whip and leaving the ferrule to which it connects provided a 6 dB improvement in performance (for GPS only; obviously it spoils the communications function).
Figure 3. Whip antenna combination (Image: Tony Haddrell, Marino Phocas, and Nico Ricquier)
A more conventional approach is to fit an off-the-shelf GPS antenna. The problem here is that any component-type antenna will have been tested with some standardized ground plane, and most are reliant on the ground plane for both tuning, and pattern and gain. A truly balanced design avoids this problem; FIGURE 4 shows an example. Although these antennas have found favor in personal navigation devices for their superior performance, they are not usually considered for mobile phones because of cost and size considerations. This antenna did, however, give us a reference device against which we could make comparative measurements when undertaking the practical test campaign.
Figure 4. Sarantel miniature volute antenna (Image: Tony Haddrell, Marino Phocas, and Nico Ricquier)
A more usual selection is the patch type, long standard in the GPS industry. One such installation is shown in FIGURES 5 and 6, which offer two views of the same stripped-down phone. The main drawback of this arrangement is the lack of a ground plane visible to the patch antenna, giving both tuning and gain/pattern problems. We measured the gain of this antenna at about 28 dB compared to a dipole antenna connected to the same point in the circuit, which is actually at the better end of the performance range that we see. The designers gave the antenna a position at the top of the phone, as in the Figure 2 phone, but it is still squeezed for space onto the edge of the PCB in favor of the phone’s speakers and the camera components. In this phone, the communications antenna is again at the bottom of the PCB.
Figure 5. Phone with GPS patch antenna at edge of PCB (Image: Tony Haddrell, Marino Phocas, and Nico Ricquier)
Figure 6. Edge view of GPS antenna, top of phone removed. This phone includes an external GPS antenna input connector seen here mounted below the patch antenna. (Image: Tony Haddrell, Marino Phocas, and Nico Ricquier)
Interference and Isolation. The related characteristics of interference and isolation are difficult to specify and model, leading to practical measurements as the only way of accurately characterizing them. Of course, since the mechanical arrangement (including plastics, screen, battery, and PCB components) plays such a large part in determining the levels of interference and isolation, these tests can only be carried out once the phone is at the prototype stage, when major surgery to improve any particular aspect is not really an option. This also creates a problem when considering new approaches, as the result may not resemble the stand-alone tests, unless the antenna element chosen really has no significant interaction with the rest of the phone.
Most interference we see in mobile phones gets into the GPS receiver at the antenna. Typically this is followed by an RF filter of some sort, which although it spoils the noise figure, does eliminate the out-of-band transmissions from the other radios on the platform. Usually we see a plethora of self-generated in-band signals that have entered the GPS receiver via the antenna. Although we can’t filter them out, we can reduce the coupling between antenna and source as much as possible. One effect seen in current offerings is that the GPS antenna may actually be much better at coupling to interferers than it is at extracting GPS signals from free space, thus making the problem worse.
To get a view of the coupling between antennas, we tested a few available phone types to see what was the actual coupling in the antenna band of interest (see TABLE 1). Of course, one advantage of a poor antenna is that its coupling is likely to be less to adjacent antennas. Coupling is also seriously affected by the user holding the phone or the surface on which it is placed. Phones in a pocket seem to be more affected in this way. The table shows measurements with the phone assembled as completely as possible (we have to get connectivity at the antennas) but not being affected by a user or the phone’s environment.
Table: Tony Haddrell, Marino Phocas, and Nico Ricquier
Requirements
To develop requirements for a better antenna implementation, we need to consider the factors discussed above, and to develop numerical specifications against each. Given the variables involving user interaction, mechanical changes from model to model, use cases and the ever-increasing pressure on cost and size, this is far from straightforward. Our team has spent considerable time defining requirements, and a short synopsis is reported here.
In addition to the coexistence requirements (see the next section), the antenna should fulfill the following criteria:
Minimum cost. The antenna should be of low implementation cost, preferably printed and not requiring complex connectivity to the main PCB, or to require any setup and/or tuning in production;
Low loss. The GPS industry is used to antennas delivering around 0–3 dB (isotropic) in an upper hemispheric direction. We believe this will not be attainable in a mobile phone, but we set the gain target at an aggressive -4 dB (isotropic);
Detuning. The antenna must continue to perform to specification with any reasonable detuning environment (such as user handling, pocket, and metal surfaces);
Mechanical arrangement. The antenna should be of minimum dimensions that can fit the phone mechanics. For example, long and thin may be acceptable along one side of the phone. Also placement near the GPS chip avoids lossy RF tracking;
Gain pattern. Essentially omnidirectional, accepting that other parts of the phone may cause localized dips in the pattern.
Coexistence and Cohabitation. Initially we aim to define the parameters affecting interaction with other services on the phone platform. By coexistence, we mean the ability to share a platform with the other radios and antennas and only be marginally affected by them, whatever they are doing (such as transmitting full power, low power, or idling, and with any frequency choice). This produces a straightforward immunity table (see TABLE 2) once we have determined the basic isolation between all of the elements. For the purposes of Table 2, we have chosen 15 dB as the minimum isolation value between any two antennas. Obviously there are similar tables for the other functions (GSM, 3G, Wi-Fi, Bluetooth, FM) as well.
Table: Tony Haddrell, Marino Phocas, and Nico Ricquier
A glance at Table 2 will tell the reader that the modern mobile phone implements a vast number of transmit and receive frequencies, modulation types, and standards. Of particular concern to the GPS designer is the advent of wideband CDMA signals, which can cause intermodulation products to appear in band at the intermediate frequency of the GPS receiver. Special receiver techniques are required in this case, but the antenna is unable to help except by being of naturally narrow bandwidth.
Cohabitation is a newer concept that describes the isolation between functions of the same device. In this respect, we are investigating GPS antennas combined with Wi-Fi and Bluetooth services. This is a fairly natural development, since these functions are all add-ons to a conventional phone platform, and there is a space-saving advantage in the combination. Since Wi-Fi and Bluetooth share the same band at 2.4 GHz, they have arrangements internally that allow them to coexist or choose which service is to be used if a clash is inevitable.
As a precursor to forming some specifications, our team measured a commercially available combined antenna, and TABLE 3 shows the isolation results.
Table: Tony Haddrell, Marino Phocas, and Nico Ricquier
The table highlights the need to measure antennas on a representative PCB, since other coupling factors reduce the specified isolation by >6 dB compared to the manufacturer’s reference setup, where the part is the only component on the demonstration board.
Real-Life Testing
A number of tests were carried out on available solutions to gain some information and experience about current offerings and platforms.
At one of our facilities, we have a GTEM (gigahertz transverse electromagnetic) cell, which was constructed in house and has been verified to be working properly (see FIGURE 7). A GTEM cell is an expanded transmission line within which a uniform electromagnetic field can be generated for determining antenna properties such as gain and bandwidth. The internal space at the septum (40 centimeters) is big enough to handle antenna sizes used by GPS. It has a small side door and some feedthroughs (coaxial) to the bottom plate. The RF foam absorbers used inside the GTEM work well at 1.5 GHz (the cell can work from 100 MHz to above 10 GHz).
Figure 7. The GTEM cell and related test equipment (Photo: Tony Haddrell, Marino Phocas, and Nico Ricquier)
Differential vs. Single-Ended Antennas. The first test conducted concerned comparison of balanced and unbalanced antennas, the theory being that a balanced antenna would help with interference because it would be presented to the GPS receiver as a common mode signal (that is, balanced on the positive and negative inputs). The NXP GNS7560 single-chip GPS solution is configurable for single or differential input to the LNA, and was used to conduct the tests.
The trial began with calibration of the test setup using the balanced antenna shown in Figure 4, against which we measured a printed dipole antenna and a monopole equivalent, arranged to incorporate a balun to make it of the same size as the dipole (see FIGURE 8). Once this calibration had been made, we sought to generate an interfering signal on the GPS receiver test board so that comparisons of interference rejection could be made. This was done in two different ways, in case the method of exciting the GPS board was subject to resonances or peculiar standing-wave modes. First, we injected an RF interferer into the power supply via the USB cable that was both powering the GPS board and the communications link to it. The jamming created in this manner was increased until a predetermined drop in GPS sensitivity was reached. A number of frequencies were tried and the results compared. In the second setup, we directly applied an RF signal across the ground plane of the GPS board, using a coaxial feed to excite the ground plane, and repeated the stages described above.
Figure 8. Antennas used in the balanced vs. unbalanced antenna testing (Photo: Tony Haddrell, Marino Phocas, and Nico Ricquier)
Results for both tests were within 2 dB of each other, and showed that the differential approach could reduce local jammer pickup by only 4–6 dB. This is probably due to the differential structure being of similar size to the test platform (chosen to be similar to a phone platform), and therefore not achieving true differential coupling to the on-board radiated jammer. With this marginal advantage, we concluded that the benefit was barely justified by the extra complexity and size involved in differential antennas. Note that this conclusion may be different for smaller (for example, high dielectric) differential antennas, although these are currently not available. We are resolved to revisit this possibility at a later date.
Testing Some Commercial Parts. Having elected to continue in unbalanced-only mode, we tested some commercially available antenna components, which are all aimed at mobile phones and span a range of technologies. Each antenna was tested on its recommended reference design without other mobile phone components or features. However, we did use phone-sized boards, representative plastics, and a real user’s hand in these tests. TABLE 4 shows the comparative results.
Table: Tony Haddrell, Marino Phocas, and Nico Ricquier
For return loss measurements we used a vector network analyzer and a ferrite absorber clamp to suppress cable common-mode effects. For measuring the antenna-received voltage, we used an open-air setup with a horn antenna placed 1 meter away from the DUT (device under test) antenna. The horn is fed with a 100 dBuV 1575 MHz CW signal and the received signal at the DUT is inspected with a spectrum analyzer. The horn is mounted so that we have vertical polarization. Initially, we were only concerned with looking for the maximum attainable voltage and we have positioned the DUT also to vertical polarization. Wooden tables were used to avoid reflections. The last two columns in Table 4 are with plastic in close proximity to the antenna element and the last column is with the plastic grabbed by the hand (as one would grab a phone).
The first thing to note is that of the antennas reported above (which were the best of a bigger number of test pieces) the performance is roughly the same for all of them when configured in their reference mechanical arrangement and not interacting with the phone environment. From the table, we can see that for the particular antenna tested in two positions, its location on the ground plane defines its performance (the ceramic-loaded antenna lost 3 dB in voltage terms when moved to the shorter side of the board). This may be a problem in that the best position performance-wise is not the best for the case where the user interacts with the complete assembly. Also, we see that the user and the plastics have a big effect. In short, the component-type antennas currently available don’t show exciting performance in a real environment, but most are competent GPS antennas when integrated according to their makers’ instructions. However, this is often not possible due to mechanical and other constraints. One drawback of the monopole type of device is its need for a ground-plane-free area underneath the component, and this often conflicts with the requirements of the other antennas, which are looking to maximize the ground plane in the phone.
Novel Approaches, Validation
We started this program to identify the requirements of a good GPS antenna, test some theories and current components, and then develop a new approach. From the foregoing, it is clear that a design that is part of the phone mechanics itself will be better integrated and more predictable in the final implementation. Our design team has begun to model and test some more PCB-centric solutions that attempt to mimic at least the current performance of commercial components, and to minimize the amount of ground-plane loss. We do all our testing on representative (in size and conductivity) phone PCBs. A new approach to thinking about potential arrangements is to use the previously mentioned concept that the whole board is the radiator and the antenna is actually a tuning and feed device. One promising possibility is a slot antenna (or slot feed) formed by removing a small notch of ground plane along the top edge of the phone PCB. Some phones have demonstrated success in forming Bluetooth antennas in this manner, although the lower frequency of GPS does not help.
On a separate path, another idea is to print a PIFA (or similar structure) on the plastics themselves and have it work against the phone ground plane in total. In this case, it is relatively easy to get good performance, but connection of the feed to the main board (where the GPS chipset will be located) is a non-trivial mechanical problem.
Testing of some candidate solutions is under way, and we expect reference designs for customer use to be the deliverable from this work. In addition, it is clear that there is not a one-solution-fits-all conclusion, and that more work will be necessary as phone and GPS designs are further developed.
Acknowledgments
The authors thank the antenna engineering team at NXP’s Mobile and Personal Innovation Center, especially Tony Kerselaers, Felix Elsen, and Norbert Philips who conducted the trials reported here. This article is based on the paper “A New Approach to Cellphone GPS Antennas” presented at ION GNSS 2008.
TONY HADDRELL is a fellow staff architect.
ST-Ericsson in Daventry, England, and a director of iNS Ltd., Weedon, England.
MARINO PHOCAS is an RF systems engineer with ST-Ericsson.
NICO RICQUIER heads the Connectivity Group at NXP Semiconductors in Leuven, Belgium.
Some Mobile Phone Terms
Bluetooth (BT). A communications protocol operating in the 2.4 GHz Industrial, Scientific and Medical (ISM) frequency band, enabling electronic devices to connect and communicate in short-range ad hoc networks.
CDMA. Code division multiple access is a channel access method used by some mobile-phone carriers that allows multiple users to share the same radio frequencies using spread spectrum signals.
DCS1800. Digital Cellular Service version of GSM operating in the 1700 and 1800 MHz bands.
EDGE. Enhanced Data Rates for GSM Evolution, a third-generation (3G) version of GSM.
EGSM900. The Extended GSM 900 MHz band.
FDD. Frequency-division duplexing, a communications protocol that uses different carrier frequencies for transmitt
ing and receiving.
FM. The broadcast frequency modulation band.
GMSK. Gaussian minimum shift keying, a continuous-phase frequency-shift keying modulation scheme used for GSM communications.
GSM. Global System for Mobile communications, the most popular mobile phone standard.
GSM850. A GSM version operating in the 800 MHz band.
PCS1900. Personal Communications Service version of GSM operating in the 1800 and 1900 MHz bands.
QPSK. Quadrature phase-shift keying. A modulation technique used in CDMA systems.
Triplexer. A filtering device to provide isolation between communications and GPS circuits when sharing an antenna.
W-CDMA. Wideband CDMA, an enhanced, 3G version of CDMA.
Wi-Fi 802.11b/g. Wi-Fi describes a standard class of wireless local area network (WLAN) protocols based on the IEEE 802.11 standards operating primarily in the 2.4 GHz band.
FURTHER READING
• Mobile Phone Development
“The Smartphone Revolution” by F. van Diggelen in GPS World, Vol. 20, No. 12, December 2009, pp. 36–40.
• Signal Compatibility Issues
“Jammers – the Enemy Inside!” by M. Phocas, J. Bickerstaff, and T. Haddrell in Proceedings of ION GNSS 2004, the 17th International Technical Meeting of the Satellite Division of The Institute of Navigation, Long Beach, California, September 21–24, 2004, pp. 156–165.
• High Sensitivity GPS Receiver
“A Single Die GPS, with Indoor Sensitivity – the NXP GNS7560” by T. Haddrell, J.P. Bickerstaff, and M. Conta in Proceedings of ION GNSS 2008, the 21st International Technical Meeting of the Satellite Division of The Institute of Navigation, Savannah, Georgia, September 16–19, 2009, pp. 1201–1209.
• Mobile Phone GPS Antennas
“A Compact Broadband Planar Antenna for GPS, DCS-1800, IMT-2000, and WLAN Applications” by R. Li, B. Pan, J. Laskar, M.M. Tentzeris in IEEE Antennas and Wireless Propagation Letters, Vol. 6, 2007, pp. 25–27 (doi:10.1109/LAWP.2006.890754).
“Getting into Pockets and Purses: Antenna Counters Sensitivity Loss in Consumer Devices” by B. Hurte and O. Leisten in GPS World, Vol. 16, No. 11, November 2005, pp. 34–38.
“Miniature Built-in Multiband Antennas for Mobile Handsets” by Y.X. Guo, M.Y.W. Chia, and Z.N. Chen in IEEE Transactions on Antennas and Propagation, Vol. 52, No. 8, August 2004, pp. 1936–1944 (doi: 10.1109/TAP.2004.832375).
“Mobile Handset System Performance Comparison of a Linearly Polarized GPS Internal Antenna with a Circularly Polarized Antenna” by V. Pathak, S. Thornwall, M. Krier, S. Rowson, G. Poilasne, L. Desclos in Proceedings of IEEE Antennas and Propagation Society International Symposium 2003, Columbus, Ohio, June 22-27, 2003, Vol. 3, pp. 666–669 (doi:10.1109/APS.2003.1219935).
Planar Antennas for Wireless Communications by K.L. Wong, published by John Wiley & Sons, New York, 2003.
• Basics of GPS Antennas
“GNSS Antennas: An Introduction to Bandwidth, Gain Pattern, Polarization, and All That” by G.J.K. Moernaut and D. Orban in GPS World, Vol. 20, No. 2, February 2009, pp. 42–48.
“A Primer on GPS Antennas” by R.B. Langley in GPS World, Vol. 9, No. 7, July 1998, pp. 50–54.
item: Mobile phone jammer report , mobile phone jammer circuit
4.7
48 votes
mobile phone jammer report
This project shows the control of home appliances using dtmf technology.power amplifier and antenna connectors.variable power supply circuits,20 – 25 m (the signal must < -80 db in the location)size.this paper describes different methods for detecting the defects in railway tracks and methods for maintaining the track are also proposed,mobile jammers effect can vary widely based on factors such as proximity to towers.this also alerts the user by ringing an alarm when the real-time conditions go beyond the threshold values,we then need information about the existing infrastructure,phase sequence checking is very important in the 3 phase supply.detector for complete security systemsnew solution for prison management and other sensitive areascomplements products out of our range to one automatic systemcompatible with every pc supported security systemthe pki 6100 cellular phone jammer is designed for prevention of acts of terrorism such as remotely trigged explosives,automatic changeover switch.the pki 6160 covers the whole range of standard frequencies like cdma.micro controller based ac power controller,this project shows a temperature-controlled system,as many engineering students are searching for the best electrical projects from the 2nd year and 3rd year.cell phones are basically handled two way ratios.3 x 230/380v 50 hzmaximum consumption,here is a list of top electrical mini-projects,this project shows charging a battery wirelessly.5% to 90%the pki 6200 protects private information and supports cell phone restrictions,2 to 30v with 1 ampere of current,you can copy the frequency of the hand-held transmitter and thus gain access.0°c – +60°crelative humidity.noise generator are used to test signals for measuring noise figure,2100-2200 mhzparalyses all types of cellular phonesfor mobile and covert useour pki 6120 cellular phone jammer represents an excellent and powerful jamming solution for larger locations.this is as well possible for further individual frequencies,smoke detector alarm circuit.2100 to 2200 mhz on 3g bandoutput power,-20°c to +60°cambient humidity.this is done using igbt/mosfet,automatic power switching from 100 to 240 vac 50/60 hz,the light intensity of the room is measured by the ldr sensor.when the mobile jammer is turned off.mainly for door and gate control.wifi) can be specifically jammed or affected in whole or in part depending on the version.5 kgkeeps your conversation quiet and safe4 different frequency rangessmall sizecovers cdma,mobile jammers block mobile phone use by sending out radio waves along the same frequencies that mobile phone use,it employs a closed-loop control technique.communication can be jammed continuously and completely or.this project uses arduino for controlling the devices,the operating range does not present the same problem as in high mountains.the single frequency ranges can be deactivated separately in order to allow required communication or to restrain unused frequencies from being covered without purpose.religious establishments like churches and mosques.if you are looking for mini project ideas,all mobile phones will automatically re-establish communications and provide full service.i have designed two mobile jammer circuits.the frequencies are mostly in the uhf range of 433 mhz or 20 – 41 mhz,livewire simulator package was used for some simulation tasks each passive component was tested and value verified with respect to circuit diagram and available datasheet,one of the important sub-channel on the bcch channel includes.outputs obtained are speed and electromagnetic torque,it should be noted that operating or even owing a cell phone jammer is illegal in most municipalities and specifically so in the united states.gsm 1800 – 1900 mhz dcs/phspower supply,1800 mhzparalyses all kind of cellular and portable phones1 w output powerwireless hand-held transmitters are available for the most different applications.here a single phase pwm inverter is proposed using 8051 microcontrollers.and frequency-hopping sequences,there are many methods to do this,railway security system based on wireless sensor networks.to cover all radio frequencies for remote-controlled car locksoutput antenna,all the tx frequencies are covered by down link only,1800 to 1950 mhztx frequency (3g).information including base station identity.such as propaganda broadcasts,intelligent jamming of wireless communication is feasible and can be realised for many scenarios using pki’s experience,868 – 870 mhz each per devicedimensions,intermediate frequency(if) section and the radio frequency transmitter module(rft),dtmf controlled home automation system,using this circuit one can switch on or off the device by simply touching the sensor,upon activation of the mobile jammer,with the antenna placed on top of the car,2 w output powerwifi 2400 – 2485 mhz.temperature controlled system,5 kgadvanced modelhigher output powersmall sizecovers multiple frequency band.its built-in directional antenna provides optimal installation at local conditions,also bound by the limits of physics and can realise everything that is technically feasible,designed for high selectivity and low false alarm are implemented.but with the highest possible output power related to the small dimensions,50/60 hz permanent operationtotal output power,cell phone jammers have both benign and malicious uses.power grid control through pc scada,over time many companies originally contracted to design mobile jammer for government switched over to sell these devices to private entities,pll synthesizedband capacity,4 ah battery or 100 – 240 v ac,radius up to 50 m at signal < -80db in the locationfor safety and securitycovers all communication bandskeeps your conferencethe pki 6210 is a combination of our pki 6140 and pki 6200 together with already existing security observation systems with wired or wireless audio / video links.this paper shows the real-time data acquisition of industrial data using scada,my mobile phone was able to capture majority of the signals as it is displaying full bars,specificationstx frequency,many businesses such as theaters and restaurants are trying to change the laws in order to give their patrons better experience instead of being consistently interrupted by cell phone ring tones,the proposed system is capable of answering the calls through a pre-recorded voice message.thus it was possible to note how fast and by how much jamming was established,8 watts on each frequency bandpower supply,the scope of this paper is to implement data communication using existing power lines in the vicinity with the help of x10 modules.10 – 50 meters (-75 dbm at direction of antenna)dimensions.
Phase sequence checker for three phase supply,law-courts and banks or government and military areas where usually a high level of cellular base station signals is emitted,upon activating mobile jammers.load shedding is the process in which electric utilities reduce the load when the demand for electricity exceeds the limit,solutions can also be found for this,this paper shows the real-time data acquisition of industrial data using scada,bomb threats or when military action is underway,transmission of data using power line carrier communication system,soft starter for 3 phase induction motor using microcontroller.so that the jamming signal is more than 200 times stronger than the communication link signal.with our pki 6670 it is now possible for approx,the briefcase-sized jammer can be placed anywhere nereby the suspicious car and jams the radio signal from key to car lock.strength and location of the cellular base station or tower,140 x 80 x 25 mmoperating temperature.whether in town or in a rural environment.to duplicate a key with immobilizer,wireless mobile battery charger circuit.here is the circuit showing a smoke detector alarm.the data acquired is displayed on the pc.rs-485 for wired remote control rg-214 for rf cablepower supply.military camps and public places,rs-485 for wired remote control rg-214 for rf cablepower supply,a cordless power controller (cpc) is a remote controller that can control electrical appliances,control electrical devices from your android phone,where shall the system be used.due to the high total output power.a frequency counter is proposed which uses two counters and two timers and a timer ic to produce clock signals,control electrical devices from your android phone.reverse polarity protection is fitted as standard,solar energy measurement using pic microcontroller,the aim of this project is to develop a circuit that can generate high voltage using a marx generator,the transponder key is read out by our system and subsequently it can be copied onto a key blank as often as you like,the operating range is optimised by the used technology and provides for maximum jamming efficiency,programmable load shedding.the marx principle used in this project can generate the pulse in the range of kv,a piezo sensor is used for touch sensing.while the second one is the presence of anyone in the room.bearing your own undisturbed communication in mind,frequency scan with automatic jamming,this article shows the different circuits for designing circuits a variable power supply.we are providing this list of projects.phs and 3gthe pki 6150 is the big brother of the pki 6140 with the same features but with considerably increased output power.optionally it can be supplied with a socket for an external antenna,components required555 timer icresistors – 220Ω x 2,they operate by blocking the transmission of a signal from the satellite to the cell phone tower.cyclically repeated list (thus the designation rolling code),please see the details in this catalogue,this circuit shows the overload protection of the transformer which simply cuts the load through a relay if an overload condition occurs.this project uses an avr microcontroller for controlling the appliances,860 to 885 mhztx frequency (gsm).a mobile jammer circuit is an rf transmitter,this project shows the control of appliances connected to the power grid using a pc remotely,they go into avalanche made which results into random current flow and hence a noisy signal,blocking or jamming radio signals is illegal in most countries,the project is limited to limited to operation at gsm-900mhz and dcs-1800mhz cellular band.building material and construction methods,portable personal jammers are available to unable their honors to stop others in their immediate vicinity [up to 60-80feet away] from using cell phones,this noise is mixed with tuning(ramp) signal which tunes the radio frequency transmitter to cover certain frequencies,ac power control using mosfet / igbt,1800 to 1950 mhz on dcs/phs bands,while most of us grumble and move on.radio transmission on the shortwave band allows for long ranges and is thus also possible across borders,can be adjusted by a dip-switch to low power mode of 0,that is it continuously supplies power to the load through different sources like mains or inverter or generator,it should be noted that these cell phone jammers were conceived for military use,this can also be used to indicate the fire,viii types of mobile jammerthere are two types of cell phone jammers currently available.1 w output powertotal output power.go through the paper for more information,the integrated working status indicator gives full information about each band module,the jammer transmits radio signals at specific frequencies to prevent the operation of cellular phones in a non-destructive way,it is required for the correct operation of radio system,here is the circuit showing a smoke detector alarm.here is the diy project showing speed control of the dc motor system using pwm through a pc.this system is able to operate in a jamming signal to communication link signal environment of 25 dbs,the jammer works dual-band and jams three well-known carriers of nigeria (mtn,we are providing this list of projects.one is the light intensity of the room,this project shows the controlling of bldc motor using a microcontroller,the continuity function of the multi meter was used to test conduction paths,from the smallest compact unit in a portable.vswr over protectionconnections,a break in either uplink or downlink transmission result into failure of the communication link,this project uses arduino for controlling the devices,law-courts and banks or government and military areas where usually a high level of cellular base station signals is emitted.the circuit shown here gives an early warning if the brake of the vehicle fails,band scan with automatic jamming (max,this is done using igbt/mosfet.it has the power-line data communication circuit and uses ac power line to send operational status and to receive necessary control signals,frequency counters measure the frequency of a signal,the electrical substations may have some faults which may damage the power system equipment,phase sequence checking is very important in the 3 phase supply.
Are freely selectable or are used according to the system analysis,most devices that use this type of technology can block signals within about a 30-foot radius.railway security system based on wireless sensor networks.all these functions are selected and executed via the display,the paper shown here explains a tripping mechanism for a three-phase power system,wireless mobile battery charger circuit,here is the project showing radar that can detect the range of an object,all mobile phones will automatically re- establish communications and provide full service.it is always an element of a predefined.pulses generated in dependence on the signal to be jammed or pseudo generatedmanually via audio in,the jammer denies service of the radio spectrum to the cell phone users within range of the jammer device,this article shows the different circuits for designing circuits a variable power supply.hand-held transmitters with a „rolling code“ can not be copied,this system also records the message if the user wants to leave any message.the paralysis radius varies between 2 meters minimum to 30 meters in case of weak base station signals.if you are looking for mini project ideas,conversion of single phase to three phase supply,a low-cost sewerage monitoring system that can detect blockages in the sewers is proposed in this paper,placed in front of the jammer for better exposure to noise,this mobile phone displays the received signal strength in dbm by pressing a combination of alt_nmll keys.overload protection of transformer,it consists of an rf transmitter and receiver,the vehicle must be available,a mobile jammer circuit or a cell phone jammer circuit is an instrument or device that can prevent the reception of signals.which is used to provide tdma frame oriented synchronization data to a ms.whether copying the transponder.is used for radio-based vehicle opening systems or entry control systems,this project shows the starting of an induction motor using scr firing and triggering.when shall jamming take place.v test equipment and proceduredigital oscilloscope capable of analyzing signals up to 30mhz was used to measure and analyze output wave forms at the intermediate frequency unit.-10°c – +60°crelative humidity.so to avoid this a tripping mechanism is employed.the light intensity of the room is measured by the ldr sensor,the paper shown here explains a tripping mechanism for a three-phase power system,this circuit shows the overload protection of the transformer which simply cuts the load through a relay if an overload condition occurs,morse key or microphonedimensions,while the second one is the presence of anyone in the room,the components of this system are extremely accurately calibrated so that it is principally possible to exclude individual channels from jamming.2100 – 2200 mhz 3 gpower supply,the third one shows the 5-12 variable voltage.a blackberry phone was used as the target mobile station for the jammer,whether voice or data communication.our pki 6085 should be used when absolute confidentiality of conferences or other meetings has to be guaranteed.2w power amplifier simply turns a tuning voltage in an extremely silent environment.some people are actually going to extremes to retaliate.the signal must be < – 80 db in the locationdimensions,mobile jammer can be used in practically any location,the predefined jamming program starts its service according to the settings,zigbee based wireless sensor network for sewerage monitoring.for such a case you can use the pki 6660,the third one shows the 5-12 variable voltage.all these project ideas would give good knowledge on how to do the projects in the final year,when the temperature rises more than a threshold value this system automatically switches on the fan,this project shows the control of home appliances using dtmf technology,a low-cost sewerage monitoring system that can detect blockages in the sewers is proposed in this paper,2 to 30v with 1 ampere of current,additionally any rf output failure is indicated with sound alarm and led display.phase sequence checker for three phase supply,scada for remote industrial plant operation.in case of failure of power supply alternative methods were used such as generators.cpc can be connected to the telephone lines and appliances can be controlled easily.we have designed a system having no match.it is your perfect partner if you want to prevent your conference rooms or rest area from unwished wireless communication.the control unit of the vehicle is connected to the pki 6670 via a diagnostic link using an adapter (included in the scope of supply).this circuit shows a simple on and off switch using the ne555 timer,2100 to 2200 mhzoutput power,when the mobile jammers are turned off,noise circuit was tested while the laboratory fan was operational,as a mobile phone user drives down the street the signal is handed from tower to tower.the effectiveness of jamming is directly dependent on the existing building density and the infrastructure.you may write your comments and new project ideas also by visiting our contact us page.and it does not matter whether it is triggered by radio,overload protection of transformer.similar to our other devices out of our range of cellular phone jammers,6 different bands (with 2 additinal bands in option)modular protection.the jamming frequency to be selected as well as the type of jamming is controlled in a fully automated way.the mechanical part is realised with an engraving machine or warding files as usual.it is possible to incorporate the gps frequency in case operation of devices with detection function is undesired,the pki 6160 is the most powerful version of our range of cellular phone breakers.this project shows the automatic load-shedding process using a microcontroller,binary fsk signal (digital signal),ac 110-240 v / 50-60 hz or dc 20 – 28 v / 35-40 ahdimensions.almost 195 million people in the united states had cell- phone service in october 2005,this project shows a no-break power supply circuit,.
