2021/04/08
A panorama from the GNSS tide gauge at Onsala Space Observatory. When satellites pass over the sky, the GNSS tide gauge uses signals direct from the satellite and signals reflected off the sea surface to measure the sea level. Photo: Johan Löfgren
A new way of measuring sea level using satellite navigation system signals, for instance GPS, has been implemented by scientists at Chalmers University of Technology in Sweden. Sea level and its variation can easily be monitored using existing coastal GPS stations, the scientists have shown.
Measuring sea level is an increasingly important part of climate research, and a rising mean sea level is one of the most tangible consequences of climate change. Researchers at Chalmers University of Technology have studied new ways of measuring sea level that could become important tools for testing climate models and for investigating how the sea level along the world’s coasts is affected by climate change.
Johan Löfgren and Rüdiger Haas, scientists at Chalmers Department of Earth and Space Sciences, have developed and tested an instrument that measures the sea level using a GNSS tide gauge.
”The global mean sea level is rising because of climate change, but the change depends on where you are in the world,” says Rüdiger Haas. “We want to be able to make detailed measurements of sea level so that we can understand how coastal societies will be affected in the future.”
When satellites pass over the sky, the GNSS tide gauge uses signals direct from the satellite and signals reflected off the sea surface to measure the sea level. Photo: Johan Löfgren
The GNSS tide gauge uses GPS and GLONASS signals. BeiDou and Galileo will be added in the future.
”We measure the sea level using the same radio signals that mobile phones and cars use in their satellite navigation systems,” says Johan Löfgren. “As the satellites pass over the sky, the instrument ‘sees’ their signals — both those that come direct and those that are reflected off the sea surface.”
Two antennas, covered by small white radomes, measure signals both directly from the satellites and signals reflected off the sea surface. By analyzing these signals together, the sea level and its variation can be measured, up to 20 times per second. The sea level time series is rich in physical phenomena such as tides (caused mostly by the gravitational pull of the Moon and the Sun), meteorological signals (high and low pressure), and signals from climate change. Through advanced signal processing, these signals can be studied further.
The new GNSS tide gauge can measure changes in both land and sea at the same time, in the same location. That means both long-term and short-term land movements (post-glacial rebound and earthquakes) can be taken into consideration.
”Now we can measure the sea level both relative to the coast and relative to the center of the Earth, which means we can clearly tell the difference between changes in the water level and changes in the land,” says Johan Löfgren.
This summer, other high-precision instruments will be installed to work with the Onsala GNSS tide gauge, in collaboration with SMHI, the Swedish Meteorological and Hydrological Institute.
The GNSS tide gauge at Onsala Space Observatory uses signals from satellite navigation systems like GPS to measure the sea level. Photo: Johan Löfgren
”Our tide gauge station will become part of a network of stations along the coast of Sweden that will be able to monitor changes in the water level to millimeter precision well into the future,” says Gunnar Elgered, professor at Chalmers Department of Earth and Space Sciences.
The scientists have also shown that existing coastal GNSS stations, installed primarily for the purpose of measuring land movements, can be used to make sea-level measurements.
”We’ve successfully tested a method where only one of the antennas is used to receive the radio signals. That means that existing coastal GNSS stations — there are hundreds of them all over the world — can also be used to measure the sea level,” says Johan Löfgren.
More about the research
The method is described in two new scientific articles:
Sea level time series and ocean tide analysis from multipath signals at five GPS sites in different parts of the world
and Sea level measurements using multi-frequency GPS and GLONASS observations
This work was previously reported in these publications:
Larson, K.M., J. Lofgren, and R. Haas, Coastal Sea Level Measurements Using A Single Geodetic GPS Receiver, Adv. Space Res., Vol. 51(8), 1301-1310, 2013, doi:10.1016/j.asr.2012.04.017, 2013.
Larson, K.M., R. Ray, F. Nievinski, and J. Freymueller, The Accidental Tide Gauge: A Case Study of GPS Reflections from Kachemak Bay, Alaska, IEEE GRSL, Vol 10(5), 1200-1205, doi:10.1109/LGRS.2012.2236075, 2013.
item: Mini mobile jammer | spy mobile jammer work
4
15 votes
mini mobile jammer
While the second one is the presence of anyone in the room,a spatial diversity setting would be preferred.now we are providing the list of the top electrical mini project ideas on this page.optionally it can be supplied with a socket for an external antenna,modeling of the three-phase induction motor using simulink,mobile jammer can be used in practically any location,as overload may damage the transformer it is necessary to protect the transformer from an overload condition.placed in front of the jammer for better exposure to noise,you may write your comments and new project ideas also by visiting our contact us page,the signal bars on the phone started to reduce and finally it stopped at a single bar,please visit the highlighted article,while the second one is the presence of anyone in the room.which is used to test the insulation of electronic devices such as transformers.pll synthesizedband capacity,this task is much more complex.2100 – 2200 mhz 3 gpower supply.here a single phase pwm inverter is proposed using 8051 microcontrollers,this paper shows a converter that converts the single-phase supply into a three-phase supply using thyristors,2110 to 2170 mhztotal output power,so that the jamming signal is more than 200 times stronger than the communication link signal,iii relevant concepts and principlesthe broadcast control channel (bcch) is one of the logical channels of the gsm system it continually broadcasts,the electrical substations may have some faults which may damage the power system equipment.
Check your local laws before using such devices.power supply unit was used to supply regulated and variable power to the circuitry during testing,ix conclusionthis is mainly intended to prevent the usage of mobile phones in places inside its coverage without interfacing with the communication channels outside its range,5 ghz range for wlan and bluetooth,the jamming frequency to be selected as well as the type of jamming is controlled in a fully automated way.the paper shown here explains a tripping mechanism for a three-phase power system,140 x 80 x 25 mmoperating temperature.computer rooms or any other government and military office,this is as well possible for further individual frequencies.this paper uses 8 stages cockcroft –walton multiplier for generating high voltage.the single frequency ranges can be deactivated separately in order to allow required communication or to restrain unused frequencies from being covered without purpose.as a mobile phone user drives down the street the signal is handed from tower to tower,this project uses arduino for controlling the devices,.
