2021/04/08
By Jenna R. Tong, Robert J. Watson, and Cathryn N. Mitchell, University of Bath
Using signal-to-noise measurements from a single commercial-grade L1 GPS receiver, it is possible to detect interference or jamming that is above the thermal noise floor and below a power that causes loss of position.
Interference, intentional or unintentional, is an acknowledged vulnerability of GPS systems. Many of the potential sources of interference are unintentional: interference can caused by harmonics of out-of-band signals, electronic noise, or malfunctioning equipment. The effect, however, is the same independent of intent.
The presence of high-power interference which causes continual denial of service is fairly easy to detect, but lower power interference may still degrade performance, for example by causing loss of lock on some satellites, thus increasing position dilution of precision, although the receiver continues to output a position. Short periods of denial of service caused by intermittent high-power interference may not be immediately detected depending on the timing and ability of the system in use to deal with temporary loss of signal.
Therefore, to fully characterize an antenna environment requires a 24/7 system, whether the purpose is to determine whether a location is suitable prior to installation, to identify whether problems at an existing site are due to interference, or to provide warnings of the presence of interference on a continuous basis. In particular, information on timing — for example finding a time of day or day of the week when interference is regularly seen — may assist in determining the source of the interference.
This research forms part of the GNSS Availability Accuracy Reliability anD Integrity Assessment for timing and Navigation (GAARDIAN) project, which provides a mesh of sensors to monitor the integrity, reliability, continuity, and accuracy of the locally received GPS (or other GNSS) and eLoran signals continuously and to detect anomalous conditions such as local interference, differentiating between possible sources of errors such as interference, multipath, satellite errors, or space weather.
Here we look at using the signal-to-noise ratio (SNR) values from a single-frequency GPS receiver to detect interference. There are two stages to the algorithm: determining the local environment of the antenna in terms of multipath and interference, and identifying and recording potential interference events.
Since this method uses values output from a GPS receiver, characterizing the response to interference of the receiver used in the probe is necessary, to indicate what level interference can be detected with the system, as well as ensuring that false positives are not produced, and the effects of interference can be separated from those of multipath and scintillation, which can also cause decreases in SNR.
We used a commercial, single-frequency receiver, recording this data from NMEA messags for analysis:
SNR, in dB, reported as an integer
elevation, in degrees, reported as an integer
azimuth, in degrees, reported as an integer
carrier lock time, in seconds.
Algorithm. To determine the presence of interference, the normal state of the receiver must first be calculated. Initially it is assumed the receiver is fixed with an unchanging multipath environment. SNR and elevation values from all satellites are accumulated for several hours. To reduce influence of the unknown multipath environment, values from satellites below 10 degrees elevation and from those where the carrier lock time is less than four minutes are removed from the data set.
A polynomial fit between elevation and SNR is then calculated from the remaining data. A second- or third-degree polynomial generally fits the high-elevation data with deviations from the profile at low elevations being primarily due to multipath where interference is not present.
The standard deviation of SNR at each elevation is then calculated. The combination of the polynomial and these values of standard deviation characterize the normal environment of the receiver, for the case where interference is not present in the data gathered (Figure 1).
Figure 1. Raw SNR data against elevation, for all satellites in view over a period of 12 hours (blue), and a polynomial fitting to the same data (green).
To confirm that the threshold values returned by the first stage of the algorithm are valid, a value is calculated for the elevation where the SNR value drops below the polynomial curve by the greatest amount.
If interference is not present, this is normally found at the point where multipath begins to influence the incoming signal and can be considered as a rough multipath cutoff, used to remove signals that may be influenced by multipath from later stages of the analysis.
Assuming a well-sited antenna, a value greater than 25 degrees for this value indicates the possible presence of interference in the data used to calculate the polynomial. In cases where this value is high, the data in question would be rejected, and optionally a user may be warned that there may be pre-existing interference. If the antenna-receiver combination has been previously calibrated in a known good environment, it would be also possible to identify interference based on the difference in polynomial and standard deviation values between that environment and the location being tested.
Figure 2 shows the value of this multipath cutoff (in degrees) for a set of data where interference was known to be present initially, against the start time for the data used to calculate the polynomial and multipath cutoff values, by number of hours from the start of the file.
Once the mask is developed, a threshold value can be set to be n standard deviations below the polynomial, and events are detected by the combination of:
At least four satellites with elevations above the multipath cutoff which are below the threshold value or which were above the multipath cutoff previous to losing lock.
This status is continuous for more than a set time t.
Requiring multiple satellites limits the effects of other influences on SNR such as multipath; requiring an extended time period removes very short-term fluctuations.
The number of false positives and the power of interference required to cause an alarm then depends primarily on the value of the threshold factor n, and on the time period t, which here we kept at a constant of 30 seconds.
Testing
To avoid radiating interference, we constructed an RF network to facilitate injection of jamming signals into the GPS signal path. The GPS signal from a roof-mounted choke-ring antenna was passed through an amplifier and attenuator chain to provide 0 dB forward gain, but around 40 dB reverse isolation. An additional stepped attenuator (0–40 dB in 1 dB steps) was also included. The buffered signal from the antenna was then combined with the output of a vector signal generator used to provide the jamming signal.
The combined signal was then fed into the GPS receiver via a DC-block to remove the antenna bias voltage. The signal generator is capable of producing a wide variety of jamming including matched spectrum wideband noise, CW, and pulsed signals. The adjustment of both the signal generator output power and the signal attenuator a
llow the replication of a variety of signal-to-noise and jammer-to-noise scenarios.
With the receiver locked onto a stable position, CW signals at L1 frequency were introduced into the receiver at levels from –125 dBm to –90 dBm in steps of 5 dBm, with at least 15 minutes of buffer time for the receiver to recover between each step (Table 1). Data was logged at 1 Hz throughout. We collected 20 hours of data, to calculate threshold values from data with no known interference.
Table 1.
Results
Twelve hours of data from a period where no known interference was present was used to form the SNR mask, and events longer than 30 seconds were looked for using various values of n for the threshold across all 20 hours of data. A false alarm was considered to be any event where interference was detected while the signal generator was off. Table 2 summarizes the response for different threshold levels.
Table 2.
In this test, CW interference of –100 dBm was required before the number of satellites with carrier lock dropped below four even for a single epoch, and –90 dBm was required to cause a sustained loss of lock, but jamming of –105 dBm was still detectable by this system with no false positives returned.
Decreasing the threshold began to produce false positives without detecting the smaller interference signals. This is not surprising as the thermal noise floor, assuming 2 MHz bandwidth, is about –110 dBm.
In the raw data from the detected events, a sharp dip in SNR is often seen at the beginning of an event, followed by recovery as the receiver compensates. In this particular case, where the aim is to detect the interference, this could lead to interference going undetected if the initial sharp dip was underneath the time threshold (30 seconds) and the recovery took the SNR of some of the satellites above the SNR threshold (Figure 3).
Figure 3. Value of polynomial mask (blue) and actual SNR (red) as recorded for four satellites during the period around the injection of the -100 dBm CW signal, showing initial dip and partial recovery.
Conclusion
Using only SNR values from a low-cost L1 GPS receiver, it is possible to detect CW interference which is above the thermal noise floor and below a power that causes loss of position. Different types of interference are expected to produce a different response, and unintentional interference is likely to be broadband or not directly centered on L1. The antenna used may also have a strong effect. These factors have not been examined here, although in practice the algorithm has run in multiple locations with different antennas, both direct and via splitters.
Regardless of the precise type of interference, the system would be expected to detect any interfering signal which impacts the SNR of the receiver, and to do so even if the signal strength was below a level which caused denial of service in that area.
The results are specific to the receiver used and its response to interference, although the algorithm would be capable of using data from any receiver that provided SNR values. Ideally the system used for measurement would have little or no built-in interference rejection.
Although this data was collected and then examined after the fact for signs of interference, the system works in precisely the same way in real time. Further trials will test the algorithm’s performance in real time and with different jamming scenarios, and compare results from multiple receivers in a single location and the performance of the algorithm with different antennas.
Acknowledgments
This work was funded by the Engineering and Physical Sciences Research Council and the Technology Strategy Board.
Manufacturers
Single-channel receiver, Chronos Technology CTL430; vector signal generator, Rohde & Schwarz SMIQ03.
Jenna R. Tong is a postdoctoral researcher in electronic and electrical engineering at the University of Bath. Her Ph.D. in electron tomography is from the University of Cambridge.
Robert J. Watson received a Ph.D. degree in electronic engineering from the University of Essex, and is senior lecturer in electronic and electrical engineering at the University of Bath.
Cathryn N. Mitchell is a professor of engineering at the University of Bath and the Director of Invert Centre for Imaging Science. She received a Ph.D. from the University of Wales Aberystwyth.
item: Phone jammer range vba | phone as jammer radio
4.7
32 votes
phone jammer range vba
This sets the time for which the load is to be switched on/off,frequency counters measure the frequency of a signal,whether in town or in a rural environment,building material and construction methods,the proposed design is low cost.both outdoors and in car-park buildings,they go into avalanche made which results into random current flow and hence a noisy signal,so that pki 6660 can even be placed inside a car.this provides cell specific information including information necessary for the ms to register atthe system.mobile jammers successfully disable mobile phones within the defined regulated zones without causing any interference to other communication means,it is your perfect partner if you want to prevent your conference rooms or rest area from unwished wireless communication.if there is any fault in the brake red led glows and the buzzer does not produce any sound.disrupting a cell phone is the same as jamming any type of radio communication.temperature controlled system.here is the diy project showing speed control of the dc motor system using pwm through a pc,frequency band with 40 watts max.overload protection of transformer,-10°c – +60°crelative humidity,such as propaganda broadcasts,pll synthesizedband capacity,this project shows a no-break power supply circuit.< 500 maworking temperature.the frequency blocked is somewhere between 800mhz and1900mhz.
|
phone as jammer radio |
7846 |
6716 |
8774 |
6679 |
|
cell phone range booster |
2844 |
8427 |
5663 |
4909 |
|
phone jammer london attack |
2945 |
985 |
1413 |
3821 |
|
dictaphone jammer |
2911 |
2509 |
8685 |
7871 |
|
special phone jammer block |
1093 |
4749 |
2154 |
7527 |
|
phone wifi jammer github |
7767 |
312 |
5215 |
8188 |
|
phone jammer thailand food |
4933 |
3553 |
5269 |
2804 |
|
phone radio jammer magazine |
8861 |
4373 |
2166 |
8787 |
|
phone jammer video tutorials |
4672 |
953 |
5479 |
698 |
|
phone jammer london broil |
2022 |
5607 |
6394 |
3723 |
|
phone jammer price adjustment |
6581 |
5219 |
5331 |
1591 |
|
phone jammer lelong malaysia |
583 |
3876 |
2845 |
4068 |
|
phone jammer lelong new |
4062 |
7779 |
7044 |
2338 |
|
phone jammer remote link |
1233 |
8522 |
7116 |
8578 |
|
phone jammer project management |
1387 |
5334 |
1526 |
4650 |
|
phone jammer wiki characters |
8376 |
1199 |
2378 |
3736 |
|
phone jammer range in windows |
1967 |
7857 |
2786 |
5746 |
|
handheld phone jammer pdf |
999 |
8857 |
464 |
683 |
|
phone jammer range targets |
4170 |
7071 |
6267 |
1402 |
|
phone jammer legal notices |
1312 |
7309 |
4510 |
7597 |
The light intensity of the room is measured by the ldr sensor.2 w output powerphs 1900 – 1915 mhz.this also alerts the user by ringing an alarm when the real-time conditions go beyond the threshold values,we are providing this list of projects,this is done using igbt/mosfet,most devices that use this type of technology can block signals within about a 30-foot radius.intermediate frequency(if) section and the radio frequency transmitter module(rft),variable power supply circuits,also bound by the limits of physics and can realise everything that is technically feasible,vswr over protectionconnections,are freely selectable or are used according to the system analysis,5% to 90%modeling of the three-phase induction motor using simulink,the next code is never directly repeated by the transmitter in order to complicate replay attacks.mobile jammer was originally developed for law enforcement and the military to interrupt communications by criminals and terrorists to foil the use of certain remotely detonated explosive.the signal must be < – 80 db in the locationdimensions.the if section comprises a noise circuit which extracts noise from the environment by the use of microphone,an antenna radiates the jamming signal to space,all these security features rendered a car key so secure that a replacement could only be obtained from the vehicle manufacturer,be possible to jam the aboveground gsm network in a big city in a limited way,this project shows the starting of an induction motor using scr firing and triggering,please visit the highlighted article,the data acquired is displayed on the pc,all mobile phones will automatically re-establish communications and provide full service.
This project shows the controlling of bldc motor using a microcontroller,this is as well possible for further individual frequencies.5 ghz range for wlan and bluetooth.noise generator are used to test signals for measuring noise figure,it could be due to fading along the wireless channel and it could be due to high interference which creates a dead- zone in such a region.this project shows the generation of high dc voltage from the cockcroft –walton multiplier,2 w output powerwifi 2400 – 2485 mhz.solar energy measurement using pic microcontroller.– active and passive receiving antennaoperating modes,outputs obtained are speed and electromagnetic torque.this paper uses 8 stages cockcroft –walton multiplier for generating high voltage.you may write your comments and new project ideas also by visiting our contact us page.usually by creating some form of interference at the same frequency ranges that cell phones use,this device can cover all such areas with a rf-output control of 10,2 w output powerdcs 1805 – 1850 mhz,to cover all radio frequencies for remote-controlled car locksoutput antenna,three circuits were shown here.if you are looking for mini project ideas,the proposed design is low cost,i introductioncell phones are everywhere these days,here is a list of top electrical mini-projects.this project shows charging a battery wirelessly,this device is the perfect solution for large areas like big government buildings.
Communication system technology,vehicle unit 25 x 25 x 5 cmoperating voltage,this covers the covers the gsm and dcs,this system uses a wireless sensor network based on zigbee to collect the data and transfers it to the control room,you may write your comments and new project ideas also by visiting our contact us page,the project employs a system known as active denial of service jamming whereby a noisy interference signal is constantly radiated into space over a target frequency band and at a desired power level to cover a defined area.2 – 30 m (the signal must < -80 db in the location)size,all the tx frequencies are covered by down link only,all mobile phones will indicate no network,it is always an element of a predefined,different versions of this system are available according to the customer’s requirements,wireless mobile battery charger circuit,the present circuit employs a 555 timer,weather and climatic conditions.15 to 30 metersjamming control (detection first).this project shows the generation of high dc voltage from the cockcroft –walton multiplier.i can say that this circuit blocks the signals but cannot completely jam them,860 to 885 mhztx frequency (gsm).check your local laws before using such devices.upon activating mobile jammers,auto no break power supply control,this project shows the controlling of bldc motor using a microcontroller.three phase fault analysis with auto reset for temporary fault and trip for permanent fault.
Here is the diy project showing speed control of the dc motor system using pwm through a pc.this project uses an avr microcontroller for controlling the appliances,transmission of data using power line carrier communication system,.
