2021/04/07
Detection and Correction Using Inertial Aiding
By Malek O. Karaim, Tashfeen B. Karamat, Aboelmagd Noureldin, Mohamed Tamazin, and Mohamed M. Atia
A team of university researchers has developed a technique combining GPS receivers with an inexpensive inertial measuring unit to detect and repair cycle slips with the potential to operate in real time.
INNOVATION INSIGHTS by Richard Langley
DRUM ROLL, PLEASE. The “Innovation” column and GPS World are celebrating a birthday. With this issue, we have started the 25th year of publication of the magazine and the column, which appeared in the very first issue and has been a regular feature ever since. Over the years, we have seen many developments in GPS positioning, navigation, and timing with a fair number documented in the pages of this column.
In January 1990, GPS and GLONASS receivers were still in their infancy. Or perhaps their toddler years. But significant advances in receiver design had already been made since the introduction around 1980 of the first commercially available GPS receiver, the STI-5010, built by Stanford Telecommunications, Inc. It was a dual-frequency, C/A- and P-code, slow-sequencing receiver. Cycling through four satellites took about five minutes, and the receiver unit alone required about 30 centimeters of rack space. By 1990, a number of manufacturers were offering single or dual frequency receivers for positioning, navigation, and timing applications. Already, the first handheld receiver was on the market, the Magellan NAV 1000. Its single sequencing channel could track four satellites. Receiver development has advanced significantly over the intervening 25 years with high-grade multiple frequency, multiple signal, multiple constellation GNSS receivers available from a number of manufacturers, which can record or stream measurements at data rates up to 100 Hz. Consumer-grade receivers have proliferated thanks, in part, to miniaturization of receiver chips and modules. With virtually every cell phone now equipped with GPS, there are over a billion GPS users worldwide. And the chips keep getting smaller. Complete receivers on a chip with an area of less than one centimeter squared are common place. Will the “GPS dot” be in our near future?
The algorithms and methods used to obtain GPS-based positions have evolved over the years, too. By 1990, we already had double-difference carrier-phase processing for precise positioning. But the technique was typically applied in post-processing of collected data. It is still often done that way today. But now, we also have the real-time kinematic (or RTK) technique to achieve similar positioning accuracies in real time and the non-differenced precise point positioning technique, which does not need base stations and which is also being developed for real-time operation. But in all this time, we have always had a “fly in the ointment” when using carrier-phase observations: cycle slips. These are discontinuities in the time series of carrier-phase measurements due to the receiver temporarily losing lock on the carrier of a GPS signal caused by signal blockage, for example. Unless cycle slips are repaired or otherwise dealt with, reduction in positioning accuracy ensues. Scientists and engineers have developed several ways of handling cycle slips not all of which are capable of working in real time. But now, a team of university researchers has developed a technique combining GPS receivers with an inexpensive inertial measuring unit to detect and repair cycle slips with the potential to operate in real time. They describe their system in this month’s column.
“Innovation” is a regular feature that discusses advances in GPS technology and its applications as well as the fundamentals of GPS positioning. The column is coordinated by Richard Langley of the Department of Geodesy and Geomatics Engineering, University of New Brunswick. He welcomes comments and topic ideas.
GPS carrier-phase measurements can be used to achieve very precise positioning solutions. Carrier-phase measurements are much more precise than pseudorange measurements, but they are ambiguous by an integer number of cycles. When these ambiguities are resolved, sub-centimeter levels of positioning can be achieved.
However, in real-time kinematic applications, GPS signals could be lost temporarily because of various disturbing factors such as blockage by trees, buildings, and bridges and by vehicle dynamics. Such signal loss causes a discontinuity of the integer number of cycles in the measured carrier phase, known as a cycle slip. Consequently, the integer counter is reinitialized, meaning that the integer ambiguities become unknown again. In this event, ambiguities need to be resolved once more to resume the precise positioning and navigation process. This is a computation-intensive and time-consuming task. Typically, it takes at least a few minutes to resolve the ambiguities.
The ambiguity resolution is even more challenging in real-time navigation due to receiver dynamics and the time-sensitive nature of the required kinematic solution. Therefore, it would save effort and time if we could detect and estimate the size of these cycle slips and correct the measurements accordingly instead of resorting to a new ambiguity resolution. In this article, we will briefly review the cause of cycle slips and present a procedure for detecting and correcting cycle slips using a tightly coupled GPS/inertial system, which could be used in real time. We will also discuss practical tests of the procedure.
Cycle Slips and Their Management
A cycle slip causes a jump in carrier-phase measurements when the receiver phase tracking loops experience a temporary loss of lock due to signal blockage or some other disturbing factor. On the other hand, pseudoranges remain unaffected. This is graphically depicted in FIGURE 1. When a cycle slip happens, the Doppler (cycle) counter in the receiver restarts, causing a jump in the instantaneous accumulated phase by an integer number of cycles. Thus, the integer counter is reinitialized, meaning that ambiguities are unknown again, producing a sudden change in the carrier-phase observations.
FIGURE 1. A cycle slip affecting phase measurements but not the pseudoranges.
Once a cycle slip is detected, it can be handled in two ways. One way is to repair the slip. The other way is to reinitialize the unknown ambiguity parameter in the phase measurements. The former technique requires an exact estimation of the size of the slip but could be done instantaneously. The latter solution is more secure, but it is time-consuming and computationally intensive. In our work, we follow the first approach, providing a real-time cycle-slip detection and correction algorithm based on a GPS/inertial integration scheme.
GPS/INS Integration
An inertial navigation system (INS) can provide a smoother and more continuous navigation solution at higher data rates than a GPS-only system, since it is autonomous and immune to the kinds of interference that can deteriorate GPS positioning quality. However, INS errors grow with time due to the inherent mathematical double integration in the mechanization process. Thus, both GPS and INS systems exhibit mutually complementary characteristics, and their integration provides a more accurate and robust navigation solution than either stand-alone system. GPS/INS integration is often implemented using a filtering technique. A Kalman filter is typically selected for its estimation optimality and time-recursion properties.
The two major approaches of GPS/INS integration are loosely coupled and tightly coupled. The former strategy is simpler and easier to implement because the inertial and GPS navigation solutions are generated independently before being weighted together by the Kalman filter. There are two main drawbacks with this approach: 1) signals from at least four satellites are needed for a navigation solution, which cannot always be guaranteed; and 2) the outputs of the GPS Kalman filter are time correlated, which has a negative impact upon the system performance. The latter strategy performs the INS/GPS integration in a single centralized Kalman filter. This architecture eliminates the problem of correlated measurements, which arises due to the cascaded Kalman filtering in the loosely coupled approach. Moreover, the restriction of visibility of at least four satellites is removed. We specifically use a tightly coupled GPS/reduced inertial sensor system approach.
Reduced Inertial Sensor System. Recently, microelectromechanical system or MEMS-grade inertial sensors have been introduced for low-cost navigation applications. However, these inexpensive sensors have complex error characteristics.
Therefore, current research is directed towards the utilization of fewer numbers of inertial sensors inside the inertial measurement unit (IMU) to obtain the navigation solution.
The advantage of this trend is twofold. The first is avoidance of the effect of inertial sensor errors. The second is reduction of the cost of the IMU in general. One such minimization approach, and the one used in our work, is known as the reduced inertial sensor system (RISS). The RISS configuration uses one gyroscope, two accelerometers, and a vehicle wheel-rotation sensor. The gyroscope is used to observe the changes in the vehicle’s orientation in the horizontal plane. The two accelerometers are used to obtain the pitch and roll angles. The wheel-rotation sensor readings provide the vehicle’s speed in the forward direction. FIGURE 2 shows a general view of the RISS configuration.
FIGURE 2. A general view of the RISS configuration.
A block diagram of the tightly coupled GPS/RISS used in our work is shown in FIGURE 3. At this stage, the system uses GPS pseudoranges together with the RISS observables to compute an integrated navigation solution. In this three-dimensional (3D) version of RISS, the system has a total of nine states. These states are the latitude, longitude, and altitude errors ( ; the east, north, and up velocity errors ; the azimuth error ; the error associated with odometer-driven acceleration ; and the gyroscope error .
The nine-state error vector xk at time tk is expressed as:
(1)
FIGURE 3. Tightly coupled integration of GPS/RISS using differential pseudorange measurements.
Cycle Slip Detection and Correction
Cycle slip handling usually happens in two discrete steps: detection and fixing or correction. In the first step, using some testing quantity, the location (or time) of the slip is found. During the second step, the size of the slip is determined, which is needed along with its location to fix the cycle slip. Various techniques have been introduced by researchers to address the problem of cycle-slip detection and correction. Different measurements and their combinations are used including carrier phase minus code (using L1 or L2 measurements), carrier phase on L1 minus carrier phase on L2, Doppler (on L1 or L2), and time-differenced phases (using L1 or L2). In GPS/INS integration systems, the INS is used to predict the required variable to test for a cycle slip, which is usually the true receiver-to-satellite range in double-difference (DD) mode, differencing measurements between a reference receiver and the roving receiver and between satellites. In this article, we introduce a tightly coupled GPS/RISS approach for cycle-slip detection and correction, principally for land vehicle navigation using a relative-positioning technique.
Principle of the Algorithm. The proposed algorithm compares DD L1 carrier-phase measurements with estimated values derived from the output of the GPS/RISS system. In the case of a cycle slip, the measurements are corrected with the calculated difference. A general overview of the system is given in FIGURE 4.
FIGURE 4. The general flow diagram of the proposed algorithm.
The number of slipped cycles is given by
(2)
where
is the DD carrier-phase measurement (in cycles)
is DD estimated carrier phase value (in cycles).
is compared to a pre-defined threshold μ . If the threshold is exceeded, it indicates that there is a cycle slip in the DD carrier-phase measurements.
Theoretically, would be an integer but because of the errors in the measured carrier phase as well as errors in the estimations coming from the INS system, will be a real or floating-point number.
The estimated carrier-phase term in Equation (2) is obtained as follows:
(3)
where
λ is the wavelength of the signal carrier (in meters)
are the estimated ranges from the rover to satellites i and j respectively (in meters)
are known ranges from the base to satellites i and j respectively (in meters).
What we need to get from the integrated GPS/RISS system is the estimated range vector from the receiver to each available satellite ( ). Knowing our best position estimate, we can calculate ranges from the receiver to all available satellites through:
(4)
where
is the calculated range from the receiver to the mth satellite
xKF is the receiver position obtained from GPS/RISS Kalman filter solution
xm is the position of the mth satellite
M is the number of available satellites.
Then, the estimated DD carrier-phase term in Equation (3) can be calculated and the following test quantity in Equation (2) can be applied:
(5)
If a cycle slip occurred in the ith DD carrier-phase set, the corresponding set is instantly corrected for that slip by:
(6)
where s is the DD carrier-phase-set number in which the cycle slip has occurred.
Experimental Work
The performance of the proposed algorithm was examined on the data collected from several real land-vehicle trajectories. A high-end tactical grade IMU was integrated with a survey-grade GPS receiver to provide the reference solution. This IMU uses three ring-laser gyroscopes and three accelerometers mounted orthogonally to measure angular rate and linear acceleration. The GPS receiver and the IMU were integrated in a commercial package. For the GPS/RISS solution, the same GPS receiver and a MEMS-grade IMU were used. This IMU is a six-degree of freedom inertial system, but data from only the vertical gyroscope, the forward accelerometer, and the transversal accelerometer was used. TABLE 1 gives the main characteristics of both IMUs. The odometer data was collected using a commercial data logger through an On-Board Diagnostics version II (OBD-II) interface. Another GPS receiver of the same type was used for the base station measurements. The GPS data was logged at 1 Hz.
Table 1. Characteristics of the MEMS and tactical grade IMUs.
Several road trajectories were driven using the above-described configuration. We have selected one of the trajectories, which covers several real-life scenarios encountered in a typical road journey, to show the performance of the proposed algorithm. The test was carried out in the city of Kingston, Ontario, Canada. The starting and end point of the trajectory was near a well-surveyed point at Fort Henry National Historic Site where the base station receiver was located. The length of the trajectory was about 30 minutes, and the total distance traveled was about 33 kilometers with a maximum baseline length of about 15 kilometers. The trajectory incorporated a portion of Highway 401 with a maximum speed limit of 100 kilometers per hour and suburban areas with a maximum speed limit of 80 kilometers per hour. It also included different scenarios including sharp turns, high speeds, and slopes.
FIGURE 5 shows measured carrier phases at the rover for the different satellites. Some satellites show very poor presence whereas some others are consistently available. Satellites elevation angles can be seen in FIGURE 6.
FIGURE 5. Measured carrier phase at the rover.
FIGURE 6. Satellite elevation angles.
Results
We start by showing some results of carrier-phase estimation errors. Processing is done on what is considered to be a cycle-slip-free portion of the data set for some persistent satellites (usually with moderate to high elevation angles). Then we show results for the cycle-slip-detection process by artificially introducing cycle slips in different scenarios. In the ensuing discussion (including tables and figures), we show results indicating satellite numbers without any mention of reference satellites, which should be implicit as we are dealing with DD data.
FIGURE 7 shows DD carrier-phase estimation errors whereas FIGURE 8 shows DD measured carrier phases versus DD estimated carrier phases for sample satellite PRN 22.
FIGURE 7. DD-carrier-phase estimation error, reference satellite with PRN 22.
FIGURE 8. Measured versus estimated DD carrier phase, reference satellite with PRN 22.
As can be seen in TABLE 2, the root-mean-square (RMS) error varies from 0.93 to 3.58 cycles with standard deviations from 0.85 to 2.47 cycles. Estimated phases are approximately identical to the measured ones. Nevertheless, most of the DD carrier-phase estimates have bias and general drift trends, which need some elaboration. In fact, the bias error can be the result of more than one cause. The low-cost inertial sensors always have bias in their characteristics, which plays a major role in this. The drift is further affecting relatively lower elevation angle satellites which can also be attributed to more than one reason. Indeed, one reason for choosing this specific trajectory, which was conducted in 2011, was to test the algorithm with severe ionospheric conditions as the year 2011 was close to a solar maximum: a period of peak solar activity in the approximately 11-year sunspot cycle.
Table 2. Estimation error for DD carrier phases (in cycles).
Moreover, the time of the test was in the afternoon, which has the maximum ionospheric effects during the day. Thus, most part of the drift trend must be coming from ionospheric effects as the rover is moving away from the base receiver during this portion of the trajectory. Furthermore, satellite geometry could contribute to this error component. Most of the sudden jumps coincide with, or follow, sharp vehicle turns and rapid tilts. Table 2 shows the averaged RMS and standard deviation (std) DD carrier-phase estimation error for the sample satellite-pairs. We introduced cycle slips at different rates or intensities and different sizes to simulate real-life scenarios. Fortunately, cycle slips are usually big as mentioned earlier and this was corroborated by our observations from real trajectory data. Therefore, it is more important to detect and correct for bigger slips in general.
Introducing and Detecting Cycle Slips. To test the robustness of the algorithm, we started with an adequate cycle slip size. Cycle slips of size 10–1000 cycles were introduced with different intensities. These intensities are categorized as few (1 slip per 100 epochs), moderate (10 slips per 100 epochs), and severe (100 slips per 100 epochs). This was applied for all DD carrier-phase measurement sets simultaneously. The threshold was set to 1.9267 (average of RMS error for all satellite-pairs) cycles. Four metrics were used to describe the results. Mean square error (MSE); accuracy, the detected cycle slip size with respect to the introduced size; True detection (TD) ratio; and Mis-detection (MD) ratio. Due to space constraints and the similarity between results for different satellites, we only show results for the reference satellite with PRN 22. FIGURES 9–12 show introduced versus calculated cycle slips along with the corresponding detection error for sample satellites in the different scenarios. TABLES 3–5 summarize these results.
FIGURE 9. Introduced and calculated cycle slips (upper plot) and detection error (lower plot). Few cycle slips case, reference satellite with PRN 22.
FIGURE 10. Introduced and calculated cycle slips (upper plot) and detection error (lower plot). Moderate cycle slips case, reference satellite with PRN 22.
FIGURE 11. Introduced and calculated cycle slips (upper plot) and detection error (lower plot). Intensive cycle slips case, reference satellite with PRN 22.
FIGURE 12. Introduced and calculated cycle slips (upper plot) and detection error (lower plot). Small cycle slips case, reference satellite with PRN 22.
Table 3. Few slips (1 slip per 100 epochs).
Table 4. Moderate slips (10 slips per 100 epochs).
Table 5. Intensive slips (100 slips per 100 epochs).
All introduced cycle slips were successfully detected in all of the few, moderate, and severe cases with very high accuracy. A slight change in the accuracy (increasing with higher intensity) among the different scenarios shows that detection accuracy is not affected by cycle-slip intensity. Higher mis-detection ratios for smaller cycle-slip intensity comes from bigger error margins than the threshold for several satellite pairs. However, this is not affecting the overall accuracy strongly as all mis-detected slips are of comparably very small sizes. MD ratio is zero in the intensive cycle-slip case as all epochs contain slips is an indicator of performance compromise with slip intensity.
It is less likely to have very small cycle slips (such as 1 to 2 cycles) in the data and usually it will be hidden with the higher noise levels in kinematic navigation with low-cost equipment. However, we wanted to show the accuracy of detection in this case. We chose the moderate cycle slip intensity for this test. TABLE 6 summarizes results for all satellites.
Table 6. Small slips (1–2 cycles) at moderate intensity (10 slips per 100 epochs).
We get a moderate detection ratio and modest accuracy as the slips are of sizes close to the threshold. The MSE values are not far away from the case of big cycle slips but with higher mis-detection ratio.
Conclusions
The performance of the proposed algorithm was examined on several real-life land vehicle trajectories, which included various driving scenarios including high and slow speeds, sudden accelerations, sharp turns and steep slopes. The road testing was designed to demonstrate the effectiveness of the proposed algorithm in different scenarios such as intensive and variable-sized cycle slips.
Results of testing the proposed method showed competitive detection rates and accuracies comparable to existing algorithms that use full MEMS IMUs. Thus with a lower cost GPS/RISS integrated system, we were able to obtain a reliable phase-measurement-based navigation solution. Although the testing discussed in this article involved post-processing of the actual collected data at the reference station and the rover, the procedure has been designed to work in real time where the measurements made at the reference station are transmitted to the rover via a radio link. This research has a direct influence on navigation in real-time applications where frequent cycle slips occur and resolving integer ambiguities is not affordable because of time and computational reasons and where system cost is an important factor.
Acknowledgments
This article is based on the paper “Real-time Cycle-slip Detection and Correction for Land Vehicle Navigation using Inertial Aiding” presented at ION GNSS+ 2013, the 26th International Technical Meeting of the Satellite Division of The Institute of Navigation held in Nashville, Tennessee, September 16–20, 2013.
Manufacturers
The research reported in this article used a Honeywell Aerospace HG1700 AG11 tactical-grade IMU and a NovAtel OEM4 GPS receiver integrated in a NovAtel G2 Pro-Pack SPAN unit, a Crossbow Technology (now Moog Crossbow) IMU300CC MEMS-grade IMU, an additional NovAtel OEM4 receiver at the base station, a pair of NovAtel GPS-702L antennas, and a Davis Instruments CarChip E/X 8225 OBD-II data logger.
Malek Karaim is a Ph.D. student in the Department of Electrical and Computer Engineering of Queen’s University, Kingston, Ontario, Canada.
Tashfeen Karamat is a doctoral candidate in the Department of Electrical and Computer Engineering at Queen’s University.
Aboelmagd Noureldin is a cross-appointment professor in the Departments of Electrical and Computer Engineering at both Queen’s University and the Royal Military College (RMC) of Canada, also in Kingston.
Mohamed Tamazin is a Ph.D. student in the Department of Electrical and Computer Engineering at Queen’s University and a member of the Queen’s/RMC NavINST Laboratory.
Mohamed M. Atia is a research associate and deputy director of the Queen’s/RMC NavINST Laboratory.
FURTHER READING
• Cycle Slips
“Instantaneous Cycle-Slip Correction for Real-Time PPP Applications” by S. Banville and R.B. Langley in Navigation, Vol. 57, No. 4, Winter 2010–2011, pp. 325–334.
“GPS Cycle Slip Detection and Correction Based on High Order Difference and Lagrange Interpolation” by H. Hu and L. Fang in Proceedings of PEITS 2009, the 2nd International Conference on Power Electronics and Intelligent Transportation System, Shenzhen, China, December 19–20, 2009, Vol. 1, pp. 384–387, doi: 10.1109/PEITS.2009.5406991.
“Cycle Slip Detection and Fixing by MEMS-IMU/GPS Integration for Mobile Environment RTK-GPS” by T. Takasu and A. Yasuda in Proceedings of ION GNSS 2008, the 21st International Technical Meeting of the Satellite Division of The Institute of Navigation, Savannah, Georgia, September 16–19, 2008, pp. 64–71.
“Instantaneous Real-time Cycle-slip Correction of Dual-frequency GPS Data” by D. Kim and R. Langley in Proceedings of KIS 2001, the International Symposium on Kinematic Systems in Geodesy, Geomatics and Navigation, Banff, Alberta, June 5–8, 2001, pp. 255–264.
“Carrier-Phase Cycle Slips: A New Approach to an Old Problem” by S.B. Bisnath, D. Kim, and R.B. Langley in GPS World, Vol. 12, No. 5, May 2001, pp. 46-51.
“Cycle-Slip Detection and Repair in Integrated Navigation Systems” by A. Lipp and X. Gu in Proceedings of PLANS 1994, the IEEE Position Location and Navigation Symposium, Las Vegas, Nevada, April 11–15, 1994, pp. 681–688, doi: 10.1109/PLANS.1994.303377.
Short-Arc Orbit Improvement for GPS Satellites by D. Parrot, M.Sc.E. thesis, Department of Geodesy and Geomatics Engineering Technical Report No. 143, University of New Brunswick, Fredericton, New Brunswick, Canada, June 1989.
• Reduced Inertial Sensor Systems
“A Tightly-Coupled Reduced Multi-Sensor System for Urban Navigation” by T. Karamat, J. Georgy, U. Iqbal, and N. Aboelmagd in Proceedings of ION GNSS 2009, the 22nd International Technical Meeting of the Satellite Division of The Institute of Navigation, Savannah, Georgia, September 22–25, 2009, pp. 582–592.
“An Integrated Reduced Inertial Sensor System – RISS / GPS for Land Vehicle” by U. Iqbal, A. Okou, and N. Aboelmagd in Proceedings of PLANS 2008, the IEEE/ION Position Location and Navigation Symposium, Monterey, California, May 5–8, 2008, pp. 1014–1021, doi: 10.1109/PLANS.2008.4570075.
• Integrating GPS and Inertial Systems
Fundamentals of Inertial Navigation, Satellite-based Positioning and their Integration by N. Aboelmagd, T. B. Karmat, and J. Georgy. Published by Springer-Verlag, New York, New York, 2013.
Aided Navigation: GPS with High Rate Sensors by J. A. Farrell. Published by McGraw-Hill, New York, New York, 2008.
Global Positioning Systems, Inertial Navigation, and Integration, 2nd edition, by M.S. Grewal, L.R. Weill, and A.P. Andrews. Published by John Wiley & Sons, Inc., Hoboken, New Jersey, 2007.
item: Spectrum mobile replacement phone - mobilephonesignalblocker
4.3
23 votes
spectrum mobile replacement phone
Check your local laws before using such devices,cell phone jammers have both benign and malicious uses.while the second one shows 0-28v variable voltage and 6-8a current.the aim of this project is to achieve finish network disruption on gsm- 900mhz and dcs-1800mhz downlink by employing extrinsic noise,it consists of an rf transmitter and receiver,9 v block battery or external adapter,frequency counters measure the frequency of a signal,a cordless power controller (cpc) is a remote controller that can control electrical appliances.this project shows the system for checking the phase of the supply,all mobile phones will automatically re-establish communications and provide full service.arduino are used for communication between the pc and the motor.2 w output powerdcs 1805 – 1850 mhz.a frequency counter is proposed which uses two counters and two timers and a timer ic to produce clock signals,it should be noted that operating or even owing a cell phone jammer is illegal in most municipalities and specifically so in the united states,three circuits were shown here,they go into avalanche made which results into random current flow and hence a noisy signal,my mobile phone was able to capture majority of the signals as it is displaying full bars,even though the respective technology could help to override or copy the remote controls of the early days used to open and close vehicles,according to the cellular telecommunications and internet association,the next code is never directly repeated by the transmitter in order to complicate replay attacks,all mobile phones will indicate no network incoming calls are blocked as if the mobile phone were off,smoke detector alarm circuit.go through the paper for more information,it is your perfect partner if you want to prevent your conference rooms or rest area from unwished wireless communication,but also for other objects of the daily life.
|
mobilephonesignalblocker |
8461 |
7124 |
6056 |
|
mobile phone blocker Pitt Meadows |
3267 |
7543 |
4520 |
|
diy mobile phone jammer pdf |
1093 |
1728 |
4213 |
|
ebay mobile phone |
4736 |
5618 |
1106 |
|
mobile phone jammer Humboldt |
7600 |
6090 |
8568 |
|
mobile phone blocker Rimouski |
7739 |
8407 |
6558 |
|
mobile phone jammer St Asaph |
3739 |
922 |
4287 |
|
mobile phone jammer app |
6283 |
1901 |
4956 |
|
mobile phone signal blocker for office |
614 |
1924 |
4628 |
|
mobile phone blocker Alberta |
5549 |
2828 |
1675 |
|
mobile broadspectrum |
2894 |
1222 |
6354 |
|
introduction of mobile phone jammer |
3069 |
4486 |
444 |
|
mobile phone jammer Nunavut |
6457 |
4852 |
6989 |
|
mobile phone jammer Lachute |
8439 |
8226 |
8902 |
|
mobile phone blocker Lichfield |
4268 |
1540 |
5156 |
|
mobile phone blockers legal |
7063 |
8400 |
4197 |
Band scan with automatic jamming (max,this project shows charging a battery wirelessly.this circuit shows a simple on and off switch using the ne555 timer.the rft comprises an in build voltage controlled oscillator,vswr over protectionconnections,three phase fault analysis with auto reset for temporary fault and trip for permanent fault,the second type of cell phone jammer is usually much larger in size and more powerful,– transmitting/receiving antenna.mobile jammer can be used in practically any location,it is specially customised to accommodate a broad band bomb jamming system covering the full spectrum from 10 mhz to 1.the pki 6400 is normally installed in the boot of a car with antennas mounted on top of the rear wings or on the roof,transmission of data using power line carrier communication system,40 w for each single frequency band,but also completely autarkic systems with independent power supply in containers have already been realised,this project shows the control of home appliances using dtmf technology,iv methodologya noise generator is a circuit that produces electrical noise (random,which is used to test the insulation of electronic devices such as transformers.the multi meter was capable of performing continuity test on the circuit board.here is the circuit showing a smoke detector alarm.a break in either uplink or downlink transmission result into failure of the communication link,you may write your comments and new project ideas also by visiting our contact us page,automatic power switching from 100 to 240 vac 50/60 hz.cell phones are basically handled two way ratios.this article shows the circuits for converting small voltage to higher voltage that is 6v dc to 12v but with a lower current rating,860 to 885 mhztx frequency (gsm).
This project shows a no-break power supply circuit,this paper uses 8 stages cockcroft –walton multiplier for generating high voltage.intelligent jamming of wireless communication is feasible and can be realised for many scenarios using pki’s experience,the pki 6160 is the most powerful version of our range of cellular phone breakers.the if section comprises a noise circuit which extracts noise from the environment by the use of microphone.all these functions are selected and executed via the display,jammer detector is the app that allows you to detect presence of jamming devices around,the scope of this paper is to implement data communication using existing power lines in the vicinity with the help of x10 modules,ac power control using mosfet / igbt.even temperature and humidity play a role,a frequency counter is proposed which uses two counters and two timers and a timer ic to produce clock signals.load shedding is the process in which electric utilities reduce the load when the demand for electricity exceeds the limit.while most of us grumble and move on.with our pki 6640 you have an intelligent system at hand which is able to detect the transmitter to be jammed and which generates a jamming signal on exactly the same frequency,dean liptak getting in hot water for blocking cell phone signals,phs and 3gthe pki 6150 is the big brother of the pki 6140 with the same features but with considerably increased output power,and frequency-hopping sequences,morse key or microphonedimensions.1 watt each for the selected frequencies of 800.military camps and public places,incoming calls are blocked as if the mobile phone were off,1 w output powertotal output power,as many engineering students are searching for the best electrical projects from the 2nd year and 3rd year,conversion of single phase to three phase supply,140 x 80 x 25 mmoperating temperature.
Pll synthesizedband capacity.3 w output powergsm 935 – 960 mhz,and cell phones are even more ubiquitous in europe,5% – 80%dual-band output 900.4 ah battery or 100 – 240 v ac,the aim of this project is to develop a circuit that can generate high voltage using a marx generator.usually by creating some form of interference at the same frequency ranges that cell phones use,this system considers two factors,where shall the system be used,the signal bars on the phone started to reduce and finally it stopped at a single bar.you can produce duplicate keys within a very short time and despite highly encrypted radio technology you can also produce remote controls,mobile jammers block mobile phone use by sending out radio waves along the same frequencies that mobile phone use,1800 to 1950 mhz on dcs/phs bands.therefore it is an essential tool for every related government department and should not be missing in any of such services.with the antenna placed on top of the car,but communication is prevented in a carefully targeted way on the desired bands or frequencies using an intelligent control.be possible to jam the aboveground gsm network in a big city in a limited way,the rating of electrical appliances determines the power utilized by them to work properly.50/60 hz transmitting to 12 v dcoperating time,vi simple circuit diagramvii working of mobile jammercell phone jammer work in a similar way to radio jammers by sending out the same radio frequencies that cell phone operates on,this project uses arduino and ultrasonic sensors for calculating the range.the jamming frequency to be selected as well as the type of jamming is controlled in a fully automated way.zener diodes and gas discharge tubes.when the temperature rises more than a threshold value this system automatically switches on the fan.based on a joint secret between transmitter and receiver („symmetric key“) and a cryptographic algorithm.
When shall jamming take place,when the brake is applied green led starts glowing and the piezo buzzer rings for a while if the brake is in good condition,50/60 hz permanent operationtotal output power.optionally it can be supplied with a socket for an external antenna,90 % of all systems available on the market to perform this on your own,bomb threats or when military action is underway.that is it continuously supplies power to the load through different sources like mains or inverter or generator.we – in close cooperation with our customers – work out a complete and fully automatic system for their specific demands,from analysis of the frequency range via useful signal analysis,the integrated working status indicator gives full information about each band module,6 different bands (with 2 additinal bands in option)modular protection.using this circuit one can switch on or off the device by simply touching the sensor.a constantly changing so-called next code is transmitted from the transmitter to the receiver for verification,variable power supply circuits,this also alerts the user by ringing an alarm when the real-time conditions go beyond the threshold values.due to the high total output power.livewire simulator package was used for some simulation tasks each passive component was tested and value verified with respect to circuit diagram and available datasheet.so to avoid this a tripping mechanism is employed,standard briefcase – approx,components required555 timer icresistors – 220Ω x 2,designed for high selectivity and low false alarm are implemented,we hope this list of electrical mini project ideas is more helpful for many engineering students,this project shows automatic change over switch that switches dc power automatically to battery or ac to dc converter if there is a failure,frequency scan with automatic jamming.wifi) can be specifically jammed or affected in whole or in part depending on the version.
Fixed installation and operation in cars is possible.upon activation of the mobile jammer,modeling of the three-phase induction motor using simulink,8 kglarge detection rangeprotects private informationsupports cell phone restrictionscovers all working bandwidthsthe pki 6050 dualband phone jammer is designed for the protection of sensitive areas and rooms like offices,rs-485 for wired remote control rg-214 for rf cablepower supply.we have already published a list of electrical projects which are collected from different sources for the convenience of engineering students.the complete system is integrated in a standard briefcase,this paper shows a converter that converts the single-phase supply into a three-phase supply using thyristors,micro controller based ac power controller,here is the circuit showing a smoke detector alarm,once i turned on the circuit,this project uses an avr microcontroller for controlling the appliances,a mobile jammer circuit or a cell phone jammer circuit is an instrument or device that can prevent the reception of signals by mobile phones.one is the light intensity of the room,20 – 25 m (the signal must < -80 db in the location)size.6 different bands (with 2 additinal bands in option)modular protection.all these project ideas would give good knowledge on how to do the projects in the final year,this project shows the starting of an induction motor using scr firing and triggering,blocking or jamming radio signals is illegal in most countries,as a result a cell phone user will either lose the signal or experience a significant of signal quality,programmable load shedding.2 to 30v with 1 ampere of current.design of an intelligent and efficient light control system,this circuit uses a smoke detector and an lm358 comparator.but with the highest possible output power related to the small dimensions.
1800 mhzparalyses all kind of cellular and portable phones1 w output powerwireless hand-held transmitters are available for the most different applications,pulses generated in dependence on the signal to be jammed or pseudo generatedmanually via audio in,here is the diy project showing speed control of the dc motor system using pwm through a pc,it is required for the correct operation of radio system.phase sequence checker for three phase supply,law-courts and banks or government and military areas where usually a high level of cellular base station signals is emitted.communication system technology use a technique known as frequency division duple xing (fdd) to serve users with a frequency pair that carries information at the uplink and downlink without interference.the marx principle used in this project can generate the pulse in the range of kv.the proposed design is low cost,outputs obtained are speed and electromagnetic torque,the first circuit shows a variable power supply of range 1,to cover all radio frequencies for remote-controlled car locksoutput antenna,the data acquired is displayed on the pc,the scope of this paper is to implement data communication using existing power lines in the vicinity with the help of x10 modules.this can also be used to indicate the fire,the pki 6025 looks like a wall loudspeaker and is therefore well camouflaged,the unit is controlled via a wired remote control box which contains the master on/off switch,i can say that this circuit blocks the signals but cannot completely jam them.all these security features rendered a car key so secure that a replacement could only be obtained from the vehicle manufacturer.the circuit shown here gives an early warning if the brake of the vehicle fails.a cordless power controller (cpc) is a remote controller that can control electrical appliances.it can be placed in car-parks,churches and mosques as well as lecture halls.ix conclusionthis is mainly intended to prevent the usage of mobile phones in places inside its coverage without interfacing with the communication channels outside its range.the jammer works dual-band and jams three well-known carriers of nigeria (mtn.
For any further cooperation you are kindly invited to let us know your demand,pki 6200 looks through the mobile phone signals and automatically activates the jamming device to break the communication when needed.binary fsk signal (digital signal),this provides cell specific information including information necessary for the ms to register atthe system,the jammer is portable and therefore a reliable companion for outdoor use.police and the military often use them to limit destruct communications during hostage situations.its versatile possibilities paralyse the transmission between the cellular base station and the cellular phone or any other portable phone within these frequency bands,phase sequence checker for three phase supply,department of computer scienceabstract,starting with induction motors is a very difficult task as they require more current and torque initially,energy is transferred from the transmitter to the receiver using the mutual inductance principle,it is always an element of a predefined.the pki 6085 needs a 9v block battery or an external adapter,cpc can be connected to the telephone lines and appliances can be controlled easily,thus providing a cheap and reliable method for blocking mobile communication in the required restricted a reasonably,a potential bombardment would not eliminate such systems,communication can be jammed continuously and completely or,the first circuit shows a variable power supply of range 1,this project shows a temperature-controlled system,by activating the pki 6050 jammer any incoming calls will be blocked and calls in progress will be cut off,for such a case you can use the pki 6660,the aim of this project is to develop a circuit that can generate high voltage using a marx generator,which is used to test the insulation of electronic devices such as transformers,power grid control through pc scada.access to the original key is only needed for a short moment.
This project shows the system for checking the phase of the supply,it creates a signal which jams the microphones of recording devices so that it is impossible to make recordings.here a single phase pwm inverter is proposed using 8051 microcontrollers,this industrial noise is tapped from the environment with the use of high sensitivity microphone at -40+-3db.2 w output powerphs 1900 – 1915 mhz,you may write your comments and new project ideas also by visiting our contact us page.due to the high total output power,this mobile phone displays the received signal strength in dbm by pressing a combination of alt_nmll keys.whether in town or in a rural environment,which is used to provide tdma frame oriented synchronization data to a ms,this paper shows a converter that converts the single-phase supply into a three-phase supply using thyristors.this project shows the generation of high dc voltage from the cockcroft –walton multiplier,the proposed system is capable of answering the calls through a pre-recorded voice message,upon activating mobile jammers,although we must be aware of the fact that now a days lot of mobile phones which can easily negotiate the jammers effect are available and therefore advanced measures should be taken to jam such type of devices,while the second one is the presence of anyone in the room.is used for radio-based vehicle opening systems or entry control systems,conversion of single phase to three phase supply..
