2021/04/13
Taking the Search out of Search and Rescue
By David W. Affens, Roy Dreibelbis, James E. Mentall, and George Theodorakos
In 1997, a Canadian government study determined that an improved search and rescue system would be one based on medium-Earth orbit satellites, which can provide full global coverage, can determine beacon location, and would need fewer ground stations. This month’s column examines the architecture of the GPS-based Distress Alerting Satellite System and takes a look at early test results.
INNOVATION INSIGHTS by Richard Langley
IT IS NOT COMMONLY KNOWN that the GPS satellites carry more than just navigation payloads. Beginning with the launch of the sixth Block I satellite in 1980, GPS satellites have carried sensors for the detection of nuclear weapons detonations to help monitor compliance with the Non-Proliferation Treaty. The payload is known as the Nuclear Detonation (NUDET) Detection System (NDS) and is jointly supported by the U.S. Air Force and the Department of Energy.
And now a third task is being assigned to the GPS satellites — that of search and rescue. Since the mid-1980s, a combination of low Earth orbit (LEO) and geostationary orbit (GEO) satellites have been used to detect and locate radio beacons activated by mariners, aviators, and others in distress virtually anywhere in the world and at any time. Some 28,000 lives have been saved worldwide since the search and rescue satellite-aided tracking, or SARSAT, system was implemented.
But the current system has some drawbacks. LEO satellites can determine a beacon’s position using the Doppler effect but their field-of-view is limited and one of them may not be in range when a beacon is activated. Furthermore, a large number of ground stations is needed to relay data from these satellites to search and rescue authorities. GEO satellites, on the other hand, have a large field of view (although missing parts of the Arctic and Antarctic), but they cannot position a beacon unless its signal contains location information provided by an integral satellite navigation receiver.
In 1997, a Canadian government study determined that a better SARSAT system would be one based on medium Earth orbit (MEO) satellites. A MEO system can provide full global coverage, determine beacon location, and do this with fewer ground stations. GPS was identified as the ideal MEO constellation.
And so was born the Distress Alerting Satellite System (DASS) that will become fully operational on Block III satellites. But already nine GPS satellites are hosting prototype hardware that is being used for proof-of-concept testing.
In this month’s column, we examine the architecture of DASS (including its relationship with the NDS), and take a look at some of the very positive test results already obtained — results that support the claim that DASS will take the search out of search and rescue.
NASA, which pioneered the technology used for the satellite-aided search and rescue capability that has saved thousands of lives worldwide since its inception nearly three decades ago, has developed new technology that will more quickly identify the locations of people in distress and reduce the risk to rescuers.
The Search and Rescue (SAR) Mission Office at the NASA Goddard Space Flight Center, in collaboration with several government agencies, has developed a next-generation satellite-aided search and rescue system, called the Distress Alerting Satellite System (DASS). NASA, the National Oceanic and Atmospheric Administration (NOAA), the U.S. Air Force, the U.S. Coast Guard, and other agencies are now completing the development and testing of the new system and expect to make it operational in the coming years after a complete constellation of DASS-equipped satellites is launched.
When completed, DASS will be able to almost instantaneously detect and locate distress signals generated by emergency beacons installed on aircraft and maritime vessels or carried by individuals, greatly enhancing the international community’s ability to rescue people in distress, This improved capability is made possible because the satellite-based instruments used to relay the emergency signals will be installed on the GPS satellites.
A recent satellite-aided rescue started on June 10, 2010, when 16-year-old Abby Sunderland on her 40-foot (12.2-meter) sailboat “Wild Eyes” encountered heavy seas approximately 2,000 miles (3,200 kilometers) west of Australia in the Indian Ocean. Her sailboat was dismasted and an emergency situation resulted. Ms. Sunderland activated her two emergency beacons whose signals were picked up by orbiting satellites. Using coordinates derived from the signals, a search plane spotted Ms. Sunderland the next day, and a day later she was rescued by a fishing boat directed to the scene. This highly publicized event is one of thousands of successful rescues made possible by years of NASA research and development.
Background
The beginnings of satellite-aided search and rescue date back to 1970, when a plane carrying two U.S congressmen crashed in a remote region of Alaska. A massive search and rescue effort was mounted, but to this day, no trace of them or their aircraft has ever been found. At the time, search for missing aircraft was conducted by search aircraft flying over thousands of square kilometers hoping to sight the missing aircraft. As a result of this tragedy, Congress recognized this inefficient search method and passed an amendment to the Occupational Safety and Health Act of 1970 requiring most aircraft flying in the United States to carry emergency locator beacons (ELTs) to provide a local homing capability. NASA then developed the technology to detect and locate an ELT from ground stations using the beacon signal relayed by satellites to provide more global coverage. This concept evolved into a highly successful international search and rescue system called COSPAS-SARSAT (COSPAS is an acronym for the Russian words “Cosmicheskaya Sistema Poiska Avariynyh Sudov,” which translates to “Space System for the Search of Vessels in Distress;” SARSAT is an acronym for Search and Rescue Satellite-Aided Tracking). Established by Canada, France, the United States, and the former Soviet Union in 1979, the system has 43 participating countries and has been instrumental in saving more than 28,000 lives worldwide, including 6,400 in the U.S. — all as a result of NASA’s innovations.
Since this auspicious beginning, NASA has continued to perform SAR research and development as a member of the National Search and Rescue Committee, and supports the National Search and Rescue Plan through an interagency memorandum of understanding with the Coast Guard, the Air Force, and NOAA. NOAA is responsible for operation of the U.S. portion of current COSPAS-SARSAT system that relies on SAR payloads on weather satellites in low-earth and geostationary orbits. As shown in Figure 1, the satellites relay distress signals from emergency beacons to a network of ground stations and ultimately to the U.S. Mission Control Center (USMCC) operated by NOAA. The USMCC distributes the alerts to the appropriate search and rescue authorities: the U.S. Air Force or the Coast Guard. The Air Force coordinates search and rescue for the mainland U.S. SAR region and operates the Air Force Rescue Coordination Center. The Coast Guard performs maritime search and rescue and oversees the U.S. national SAR policy.
FIGURE 1. Overall concept of search and rescue system. (Image: Cospas-Sarsat)
Beacons
Three types of distress emergency locator beacons are in use that are compatible with the COSPAS-SARSAT system:
EPIRBs (emergency position-indicating radio beacons) designed for maritime use.
ELTs (emergency locator transmitters) for use on aircraft.
PLBs (personal locator beacons) for personal use. These can be used by persons engaged in high-risk activities such as mountain climbing and backcountry skiing.
Originally, emergency locator beacons transmitted an analog signal on two frequencies: 121.5 MHz and 243 MHz in the civil and military aeronautical communications bands, respectively, so that they would be audible over aircraft radios. Later, a signal that was encoded with a digital message and transmitted at 406 MHz was added. Since February 1, 2009, only the 406-MHz-encoded signals are relayed by satellites supporting the international COSPAS-SARSAT system. Therefore, older beacons that only transmit the 121.5/243-MHz signals are now only detectable by ground-based receivers and aircraft overflying a crash site.
The 406-MHz beacons transmit an approximately half-second message, or burst, approximately every 50 seconds, beginning 50 seconds after being activated. The actual time of burst transmission is dithered in time so that no two beacons will have all of their bursts coincident. A 406-MHz beacon may also have an integral global navigation satellite system (GNSS) receiver. Such a beacon uses the GNSS receiver to attempt to determine its location for inclusion in the transmitted digital message. In this way, the beacon will be located once it is detected by a low-Earth-orbit (LEO) or geostationary orbit (GEO) satellite.
Distress messages contain information such as:
The beacon’s country of origin.
A unique 15-digit hexadecimal beacon ID.
Location, when equipped with an integrated GNSS receiver.
Whether or not the beacon contains a 121.5-MHz homing signal.
Room for Improvement
SARSAT first became operational in the mid-1980s. The current system uses instruments placed on LEO and GEO weather satellites to detect and locate mariners, aviators, and recreational enthusiasts in distress almost anywhere in the world at anytime and in almost any condition. Previously, dedicated Russian LEO satellites were also implemented but the use of these satellites was discontinued in 2007.
Although it has proven its effectiveness, as evidenced by the number of persons rescued over the system’s lifetime, the current capability does have limitations. LEO spacecraft orbit the Earth 14 times a day and use the Doppler effect with satellite orbital ephemeris data to calculate the position of a beacon. However, a satellite may not be in a position to pick up a distress signal the moment a user activates the beacon. Time is critical in responding to an emergency situation. Unfortunately, delays of two hours or longer are possible, especially near the equator.
LEO spacecraft carry two instruments: a Search and Rescue Repeater (SARR) supplied by the Canadian Department of National Defence, and a Search and Rescue Processor (SARP) provided by the French Centre National d’Etudes Spatiales (CNES). The SARR is a pure repeater, which relays the beacon signal to a local ground station where the data is analyzed to obtain a location. The SARP processes the received beacon signal by measuring the Doppler shift as a function of time, and decoding the digital message included in the 406-MHz signal. This information is stored until it can be transmitted to a ground station using the SARR’s downlink transmitter. Under most conditions beacon locations can be determined to within a radius of 5 kilometers.
Geostationary weather satellites, on the other hand, orbit above the Earth in a fixed location over the equator. Although they do provide continuous visibility of much of the Earth, they cannot independently locate a beacon unless it contains a GNSS receiver that determines its position and includes it in the beacon’s digital message. Currently, not all beacons contain integral GNSS receivers. Furthermore, even if a beacon contains a GNSS receiver, the navigation signal may be obstructed by terrain or thick foliage.
The next-generation system, DASS, overcomes these limitations and will improve accuracy and response time to provide an even more capable life-saving system.
Distress Alerting Satellite System
A 1997 Canadian government study of possible alternative satellite systems for SARSAT, including commercial sources, determined that the ideal system is based on medium Earth orbit (MEO) satellites. A MEO system will be able to provide superior global detection and location data with fewer ground stations than the existing COSPAS-SARSAT system. The GPS constellation was identified as an ideal MEO platform.
The concept of the DASS system is straightforward. Three or more antennas track different GPS satellites equipped with search and rescue repeaters that receive the distress signal and retransmit the signal to the ground. Since each satellite is in a different orbit, each received signal has a different Doppler-shifted arrival frequency and time of arrival. Knowing the position and orbit of each satellite, it is possible to determine the position of the distress beacon.
Future improvement in location accuracy is made possible by one of the strengths of the DASS space segment. That is, the DASS location algorithm optimizes location accuracy utilizing time and frequency measurements of beacon signals that were not designed for that purpose. The DASS space segment allows for the beacon signal to be modified in the future, enhancing the performance of this type of location process.
Other advantages of DASS over the existing system are fairly obvious. Reception of the emergency signal is immediate. Locations can be determined after receiving a single beacon burst since it does not rely on measuring the Doppler shift over time to determine position, as in the current LEO system. A full constellation of DASS-equipped GPS satellites in orbit will ensure that four or more satellites are in view of the transmitting emergency beacon anywhere in the world while requiring fewer ground stations.
Another key strength of the DASS system is the promise of SARSAT transponders on each satellite in the large and well-managed GPS constellation. There are at least 24 GPS active satellites in orbit at any given time (currently, 31 are active). When the GPS constellation is fully populated by satellites with DASS transponders, it will provide global coverage for satellite-supported search and rescue and provide capabilities for rapid detection and location of distress beacons.
Efforts are ongoing to integrate a satellite beacon repeater instrument, to be provided by the Canadian government, onto the GPS Block III B and C satellites to provide the DASS space segment for operational use.
DASS Development
DASS development will proceed in phases referred to as the definition and development, proof of concept, demonstration and evaluation, initial operating capability, and final operating capability. The proof of concept (POC) phase was completed in January 2009. The POC testing and results are summarized in this article. At the time of this writing, preparations are ongoing to initiate the demonstration and evaluation phase.
Definition and Development. In 2000, as part of the definition and development phase, the NASA GSFC SAR Mission Office began discussions with the Department of Energy’s Sandia National Laboratories (SNL) to determine if it would be feasible to add a SAR repeater function to a Department of Energy (DOE) instrument on GPS satellites. Sandia representatives thought it possible, and NASA agreed to fund a study to determine if, with minor modification, one could include a search and rescue repeater function to their instrument. The SNL feasibility study concluded that the GPS DOE package could, with minor modifications, perform the SAR mission. The study also determined that accurate locations could be calculated after a single beacon transmission and improved with each subsequent beacon transmission. Based on this information, NASA, with the cooperation of the U.S. Air Force Space Command and SNL, proceeded with the development of the new space-based search and rescue system, which was named the Distress Alerting Satellite System.
Proof of Concept. In 2003, a memorandum of agreement (MOA) between NASA, NOAA, the Air Force, the Coast Guard, and the Department of Energy tasked NASA to perform a POC program for DASS. The MOA included the development of a POC space segment and a prototype ground station to perform post-launch checkout, performance testing, and implementation planning of an operational DASS system. It stressed the need for DASS, gave authority to each participating agency to participate in the POC demonstration, and defined the roles of each.
The Air Force Space Command approved the addition of modified equipment on GPS satellites. The DASS POC space segment operates as a subcomponent of GPS Block IIR and IIF satellites. Nine GPS Block IIR satellites carry experimental DASS payloads, and all 12 IIF satellites are scheduled to. Therefore, the final POC space segment will consist of 21 DASS-equipped GPS satellites. Each payload receives 406-MHz SAR signals on an extant GPS UHF antenna and relays the signals at a GPS S-band frequency on a second extant antenna.
It is important to note that the performance of the DASS POC space segment will be exceeded by the performance of the operational space segment being designed specifically for DASS and planned for launch on GPS Block III satellites.
A prototype DASS ground station (Figure 2) was funded by NASA and installed at GSFC. The DASS prototype ground system consists of four antennas, four receivers, and the workstations and servers necessary to process the received data, command and control the operation of the ground station, and display and analyze the results. The antennas are located on the corners of the roof of a building connected by fiber-optic cable to signal processing equipment located in another building two kilometers away.
FIGURE 2. Prototype ground station at NASA GSFC. (Images: NASA)
Proof of Concept Testing
The overall objectives of the POC tests were to demonstrate the effectiveness of the DASS concept and to define its technical and operational characteristics. The primary technical objective was to demonstrate the system’s ability to detect and locate 406-MHz emergency beacons under various controlled conditions. This is the most important measure of the system’s ability to perform as expected.
The specific objectives of the DASS POC demonstration were to
Confirm the expected performance of the DASS concept.
Determine if new or enhanced requirements needed to be established.
Define preliminary performance levels that will be used to establish the scope and content of the next phase of development, referred to as the demonstration and evaluation phase.
Therefore, during POC testing, performance measurements were taken for the probability of detection, probability of location, and location accuracy, defined as follows.
Probability of detection is the probability of detecting the transmission of a 406-MHz beacon and recovering a valid beacon message from any available satellite.
Probability of location is the probability of obtaining a location solution within a given time after beacon activation, independently of any encoded position data in the 406-MHz beacon message.
Location accuracy is the distance from the location solution obtained within 5 minutes after beacon activation, to the actual beacon location. The required performance is specified as the probability that a given solution is within a given distance of the actual location.
It is important to note that the predicted performance of DASS assumes a full constellation of DASS-equipped GPS satellites. In fact, one of the key strengths of DASS is the promise of DASS transponders on each satellite in the GPS constellation. When a full constellation is equipped with DASS transponders, there will typically be between seven and 13 GPS satellites visible at the NASA ground station. Thus, it will be possible to schedule the ground-station antennas to receive data from the best satellites in terms of geometry, signal strength, processing capability, and other factors.
However, at the time of the POC testing, there were only eight GPS satellites equipped with DASS transponders. A maximum of three DASS-equipped GPS satellites were visible at the same time at the NASA ground station (above a 15-degree elevation angle), and there were times when only one DASS-equipped GPS satellite was visible. Thus, it was impossible to optimize satellite selection since there was never an opportunity to select from an excess of satellites that a full constellation would provide.
In particular, satellite geometry and its effect on performance is never as optimal as what would be obtained from a full constellation of GPS satellites. To predict the results of a full constellation using the results from a severely reduced constellation, a calculation based on “dilution of precision” was used.
Dilution of precision (DOP) or geometric dilution of precision, to be specific, is used to describe the geometric strength of satellite configuration on GPS accuracy. When visible satellites are close together in the sky, the geometry is said to be weak and the DOP value is high; when far apart, the geometry is strong and the DOP value is low. Thus a low DOP value gives rise to a better GPS positional accuracy due to the wider angular separation between the satellites used to calculate a beacon’s position.
Location accuracy results can be scaled to reflect the true DOP that would be obtained by a satellite constellation of 24 GPS satellites. The DOP error caused by uncertainty in time and frequency measurements is used for scaling. The DOP of the satellites actually used to calculate a location solution, denoted by ftDOPACT, is always bigger than the DOP that would have been available from a constellation of 24 GPS satellites, ftDOP24. The raw location errors need to be multiplied by the ratio ftDOP24 / ftDOPACT to reflect the results that would have been obtained if all 24 satellites were present.
The raw average location error, erravg, is given by the following:
err(b) = err(lat(b),lon(b))= distance from the known location to (lat(b),lon(b))
erravg(b0) = err(latavg(b0),lonavg(b0))
where Ω(b0) is the set of seven or fewer consecutive burst locations within 5 minutes, starting with burst b0.
The scaled location error is the location error scaled by the DOP ratio:
Since DOP changes little over 5 minutes, the error of the average is approximately
where ftDOPACT(b) is the time-frequency DOP of burst b calculated with either three or four satellite geometries depending on
the number of measurements used in the location calculation.
Test Source
A custom-designed beacon simulator was used to generate the transmissions of multiple COSPAS-SARSAT 406-MHz beacons over an extended period of time. To represent expected operational realism in the tests, the beacon simulator was used to transmit beacons at the limits of the five major beacon parameters specified by COSPAS-SARSAT as well as the nominal values. The five major beacon parameters are transmit power, modulation index, bit rate, un-modulated carrier duration, and modulation rise and fall times (see TABLE 1).
Table 1. Cospas-Sarsat beacon specifications. (Data: Cospas-Sarsat)
During POC testing, five beacons were transmitted using three scenarios: maximum beacon parameter values, minimum beacon parameter values, and variable power. The parameter values changed in each test scenario and are highlighted in TABLE 2. Beacon detection and location performance is measured for periods when there are three or more satellites visible at the same time, and for durations sufficient to collect a statistically significant amount of data.
Table 2. Beacon parameter values for each test scenario. (Data: Authors)
Two characteristics of the test source that affect system performance are the beacon antenna pattern and ground mask. To simulate beacons, the beacon simulator has a monopole antenna with the gain pattern shown in Figure 3. There is a substantial reduction in the transmitted signal at high-elevation angles (above 60°). DASS-equipped GPS satellites are often at high-elevation angles during a typical day. As expected, the effect of the pattern on test results can clearly be seen upon close inspection of the data. However, the beacon antenna pattern is an unavoidable reality and is, therefore, fully represented in the data used to generate the results presented here. Additionally, there were significant ground obstructions of the beacon signal in certain directions. The effect of beacon antenna pattern is fully included in the results presented in this article, but ground mask is taken into account by limiting satellite visibility to an elevation cut-off angle of 15 degrees.
FIGURE 3. Beacon simulator transmit antenna gain pattern.
POC Test Results
In this section, we discuss the POC test results in terms of probability of detection, probability of location, and location accuracy.
Probability of Detection. As previously mentioned, probability of detection is the probability of detecting the transmission of a 406-MHz beacon and recovering a valid beacon message from any available satellite. The requirement is that 95 percent of individual transmitted messages are detected.
Test results are given in TABLE 3 and show that the probability of detection is approximately 99 percent for all scenarios, even though only three satellites were in view at a time. Obviously, the probability of detection is dependent on the number of available satellites and performance would improve with continuous coverage by four or more satellites.
Table 3. Probability of detection test results. (Data: Authors)
Probability of Location. Again, the probability of location is the probability of obtaining a location solution within a given time after beacon activation, independently of any encoded position data in the 406-MHz beacon message. The requirement is that the probability of calculating a beacon location is 98 percent within 5 minutes.
Since the probability of location is dependent on the number of visible satellites, our performance was limited by the reduced constellation of DASS-equipped satellites. Results from periods of three-satellite coverage were 85 percent within 5 minutes, 92 percent within 10 minutes, and 94 percent within 15 minutes.
Again, the probability of location is dependent on the number of visible satellites, and performance would improve with continuous coverage by four or more satellites. To investigate the possible improvement with enhanced satellite coverage, we reduced the minimum satellite elevation angle from 15 to 10 degrees. This allowed a fourth satellite to become visible for a limited time at very low elevation angles. Even though the signal quality from such a satellite was poor, the probability of location during this period of four-satellite coverage improved as follows: 91 percent within 5 minutes, 96 percent within 10 minutes, and 97 percent within 15 minutes.
As can be seen from these results, even adding a satellite with a very low elevation-angle pass significantly improves performance. The expectation is that having a full constellation of satellites available would improve performance even more. Furthermore, the increase in satellite performance expected in the operational system will also improve probabilities of detection and location.
Location Accuracy. Recall that location accuracy is measured as the percentage of location solutions obtained within five minutes after beacon activation that are within five kilometers of the actual beacon location.
The requirement is to obtain 95 percent of the locations to within 5 kilometers of the actual location and 98 percent within 10 kilometers within five minutes after beacon activation.
As mentioned earlier, the requirements included in the performance specification assume a constellation of 24 DASS-equipped GPS satellites. POC testing was done with a system that had only eight DASS-equipped GPS satellites available. However, location errors can be scaled to reflect what the DOP would be if the satellite constellation contained all 24 GPS satellites. Therefore, it is the scaled results that can be used to determine whether performance will meet the requirement.
TABLE 4, therefore, presents the location accuracy results as measured, and after being scaled by DOP.
Table 4. Location accuracy for 5-minute periods. (Data: Authors)
Another important performance metric for DASS is location accuracy obtained after a single beacon burst is received. Even though there is not currently a requirement for single burst location accuracy, it is a very desirable feature of DASS since an emergency situation does not guarantee that more than a single burst will be received. Single burst location accuracy was, therefore, measured with the results shown in TABLE 5. Once again, the results are scaled by DOP values to remove the effect of non-optimal satellite geometry.
Table 5. Single burst location accuracy. (Data: Authors)
More insight into this performance can be gained by examining the single burst location accuracy distribution as a function of distance error, as shown in TABLE 6. It can be seen that, for these beacons, computed locations are within 9 kilometers of the actual location 95 percent of the time. Again, the expectation is that having a full constellation of satellites available would improve this performance. For instance, having more satellites to choose from might allow the system to select data from satellites with stronger or less noisy links.
Table 6. Single burst location accuracy by distance error. (Data authors)
Conclusion
The promise of search and rescue instruments on each satellite in the large and well-managed GPS constellation will provide a significant advancement in the capabilities of the already highly successful COSPAS-SARSAT system. The new system will provide global coverage for satellite-supported search and rescue and provide capabilities for rapid detection and location of distress beacons while requiring fewer ground stations.
The DASS POC system has validated, by test, the predictions made by analysis during the definition and development phase. The DASS POC testing has demonstrated reliable detection and accurate location of beacons within five minutes of activation. Accurate locations are also produced after even a single burst of a newly activated beacon, which is a desirable feature of DASS, since an emergency situation does not guarantee that more than a single burst will be received.
The performance obtained using a reduced constellation of satellites equipped with a modified, existing instrument not only demonstrates the existing capability, but also confirms the improvements to come with the operational system. In fact, the success of DASS is being emulated by the European Union in the design of their future Galileo GNSS constellation and the Russians in an upgraded GLONASS GNSS constellation, all of which will be interoperable by international agreement.
DASS will contribute to NASA’s goal of taking the search out of search and rescue. Achieving this goal will not only improve the chances of rescuing people in distress quickly, which is critical to their survival; it will also reduce the risk to rescuers who often put themselves in dangerous situations to affect a rescue. That is why the motto of the Search and Rescue Office is “Saving more lives, reducing risks to search personnel, and saving resources.”
David W. Affens is the manager of the NASA Search and Rescue (SAR) Mission Office at the Goddard Space Flight Center (GSFC) in Greenbelt, Maryland, where he began working in 1990. He holds a degree in electronic engineering. Before joining NASA, he worked in various aspects of submarine warfare and intelligence gathering for the U.S. Navy over a span of 21 years.
Roy Dreibelbis is a consultant who has worked in rescue-related jobs since 1957, including helicopter rescue missions in Vietnam. As an officer in the U.S. Air Force, he was the director of Inland SAR at rescue headquarters for the coterminous 48 states, was commander of the 33rd Air Rescue Squadron, and served as deputy chief of staff for rescue operations at rescue headquarters from 1979 until 1981. Upon retirement from the Air Force, he was employed by the State of Louisiana as flight operations director and chief pilot. In 1987, he accepted employment with contractors in the District of Columbia area that supported NASA and NOAA SARSAT activities.
James E. Mentall is the NASA/GSFC Search and Rescue Instrument Manager. He has a Ph.D. in physics and has spent more than 42 years of his professional life at GSFC. For 15 of those years, he has been responsible for the integration and test of the Search and Rescue Repeater and the Search and Rescue Processor on the NOAA Polar-orbiting Operational Weather Satellites. He has also served as the deputy mission manager for the Search and Rescue Mission Office and played a significant role in the procurement of the DASS antenna system and ground station.
George Theodorakos is the chief staff engineer for MEI Technologies, Inc. He received his B.S. summa cum laude and M.S. degrees in electrical engineering from the University of Maryland, College Park, Maryland, in 1978 and 1987, respectively. Since 2002, in his role as chief staff engineer at MEI, he has provided technical management support to the Search and Rescue Mission Office at GSFC.
FURTHER READING
• Distress Alerting Satellite System (DASS)
“Distress Alerting Satellite System (DASS)” on the NASA Search and Rescue Mission Office website, Goddard Space Flight Center, Greenbelt, Maryland.
• Search and Rescue Satellite-Aided Tracking (SARSAT)
“Search and Rescue,” Chapter 6 in Review of the Space Communications Program of NASA’s Space Operations Mission Directorate by the Committee to Review NASA’s Space Communications Program, Aeronautics and Space Engineering Board, Division on Engineering and Physical Sciences, National Research Council, published by the National Academies Press, Washington, D.C., 2007.
National Search and Rescue Plan of the United States, authored on behalf of the National Search and Rescue Committee by the United States Coast Guard, Washington, D.C.
• Medium Earth Orbit Search and Rescue (MEOSAR) Systems
COSPAS-SARSAT 406 MHz MEOSAR Implementation Plan, C/S R.012 Issue 1 —Revision 6 October 2010, COSPAS-SARSAT Secretariat, Montréal, Canada.
“SAR/Galileo Early Service Demonstration & the MEOLUT Terminal” by Indra Espacio, a presentation at Galileo Application Days, Brussels, Belgium, March 3–5 2010.
“Mid-Earth Orbiting Search and Rescue (MEOSAR) Transition to Operations” by C. O’Connors, a presentation at the Rescue Coordination Centers Controller Conference, Suitland, Maryland, February 23–25, 2010.
“Overview of MEOSAR System Status” by J. King, a presentation at BMW-2009, Beacon Manufacturers Workshop, St. Pete Beach, May 8, 2009.
“MEOSAR to the Rescue” by J. King in Channels, the EMS SATCOM Quarterly, published by EMS Technologies, Inc., January 31, 2007.
• Nuclear Detonation (NUDET) Detection System
“Detecting Nuclear Detonations with GPS” by P.R. Higbie and N.K. Blocker in GPS World, Vol. 5, No. 2, February 1994, pp. 48–50.
item: Mobile phone jammer cct , mobile phone jammer works
4.8
22 votes
mobile phone jammer cct
Therefore it is an essential tool for every related government department and should not be missing in any of such services,this paper shows the real-time data acquisition of industrial data using scada.the pki 6200 features achieve active stripping filters,pll synthesizedband capacity,230 vusb connectiondimensions.the marx principle used in this project can generate the pulse in the range of kv,and cell phones are even more ubiquitous in europe.here a single phase pwm inverter is proposed using 8051 microcontrollers,but with the highest possible output power related to the small dimensions,some people are actually going to extremes to retaliate.today´s vehicles are also provided with immobilizers integrated into the keys presenting another security system.mobile jammers successfully disable mobile phones within the defined regulated zones without causing any interference to other communication means,they go into avalanche made which results into random current flow and hence a noisy signal,intelligent jamming of wireless communication is feasible and can be realised for many scenarios using pki’s experience,the effectiveness of jamming is directly dependent on the existing building density and the infrastructure.protection of sensitive areas and facilities.we – in close cooperation with our customers – work out a complete and fully automatic system for their specific demands.8 watts on each frequency bandpower supply.so to avoid this a tripping mechanism is employed,a spatial diversity setting would be preferred,this project shows the measuring of solar energy using pic microcontroller and sensors,the multi meter was capable of performing continuity test on the circuit board,over time many companies originally contracted to design mobile jammer for government switched over to sell these devices to private entities.conversion of single phase to three phase supply,that is it continuously supplies power to the load through different sources like mains or inverter or generator,usually by creating some form of interference at the same frequency ranges that cell phones use.1 w output powertotal output power,the whole system is powered by an integrated rechargeable battery with external charger or directly from 12 vdc car battery,a blackberry phone was used as the target mobile station for the jammer,many businesses such as theaters and restaurants are trying to change the laws in order to give their patrons better experience instead of being consistently interrupted by cell phone ring tones,please see the details in this catalogue,this project shows charging a battery wirelessly,soft starter for 3 phase induction motor using microcontroller,from the smallest compact unit in a portable.this sets the time for which the load is to be switched on/off.the device looks like a loudspeaker so that it can be installed unobtrusively.the vehicle must be available.– transmitting/receiving antenna,the duplication of a remote control requires more effort,its versatile possibilities paralyse the transmission between the cellular base station and the cellular phone or any other portable phone within these frequency bands.this project shows the controlling of bldc motor using a microcontroller,similar to our other devices out of our range of cellular phone jammers.pki 6200 looks through the mobile phone signals and automatically activates the jamming device to break the communication when needed,automatic changeover switch.can be adjusted by a dip-switch to low power mode of 0,the integrated working status indicator gives full information about each band module,this paper describes the simulation model of a three-phase induction motor using matlab simulink,building material and construction methods,go through the paper for more information,a cell phone works by interacting the service network through a cell tower as base station,the frequencies extractable this way can be used for your own task forces.
9 v block battery or external adapter,solar energy measurement using pic microcontroller.disrupting a cell phone is the same as jamming any type of radio communication,-20°c to +60°cambient humidity.for such a case you can use the pki 6660.band scan with automatic jamming (max,generation of hvdc from voltage multiplier using marx generator.law-courts and banks or government and military areas where usually a high level of cellular base station signals is emitted,110 – 220 v ac / 5 v dcradius,transmission of data using power line carrier communication system.it consists of an rf transmitter and receiver.if there is any fault in the brake red led glows and the buzzer does not produce any sound,normally he does not check afterwards if the doors are really locked or not,exact coverage control furthermore is enhanced through the unique feature of the jammer,rs-485 for wired remote control rg-214 for rf cablepower supply,three phase fault analysis with auto reset for temporary fault and trip for permanent fault,one of the important sub-channel on the bcch channel includes,this project uses an avr microcontroller for controlling the appliances,cpc can be connected to the telephone lines and appliances can be controlled easily,the electrical substations may have some faults which may damage the power system equipment.components required555 timer icresistors – 220Ω x 2,to duplicate a key with immobilizer.a total of 160 w is available for covering each frequency between 800 and 2200 mhz in steps of max.design of an intelligent and efficient light control system,also bound by the limits of physics and can realise everything that is technically feasible,2 w output power3g 2010 – 2170 mhz.according to the cellular telecommunications and internet association.radio remote controls (remote detonation devices).so that the jamming signal is more than 200 times stronger than the communication link signal,mobile jammers effect can vary widely based on factors such as proximity to towers,1800 to 1950 mhztx frequency (3g),this can also be used to indicate the fire.synchronization channel (sch),phase sequence checker for three phase supply.so to avoid this a tripping mechanism is employed,now we are providing the list of the top electrical mini project ideas on this page.but are used in places where a phone call would be particularly disruptive like temples,complete infrastructures (gsm,you can control the entire wireless communication using this system,the operating range does not present the same problem as in high mountains,this system is able to operate in a jamming signal to communication link signal environment of 25 dbs.rs-485 for wired remote control rg-214 for rf cablepower supply,jamming these transmission paths with the usual jammers is only feasible for limited areas,please visit the highlighted article,an optional analogue fm spread spectrum radio link is available on request,shopping malls and churches all suffer from the spread of cell phones because not all cell phone users know when to stop talking.this project uses arduino and ultrasonic sensors for calculating the range,each band is designed with individual detection circuits for highest possible sensitivity and consistency.the paper shown here explains a tripping mechanism for a three-phase power system,the jammer transmits radio signals at specific frequencies to prevent the operation of cellular phones in a non-destructive way,at every frequency band the user can select the required output power between 3 and 1.
Incoming calls are blocked as if the mobile phone were off,intermediate frequency(if) section and the radio frequency transmitter module(rft),dtmf controlled home automation system,the jammer is portable and therefore a reliable companion for outdoor use,this paper uses 8 stages cockcroft –walton multiplier for generating high voltage.3 x 230/380v 50 hzmaximum consumption,go through the paper for more information,strength and location of the cellular base station or tower,which broadcasts radio signals in the same (or similar) frequency range of the gsm communication.transmitting to 12 vdc by ac adapterjamming range – radius up to 20 meters at < -80db in the locationdimensions,its total output power is 400 w rms.we have designed a system having no match.vi simple circuit diagramvii working of mobile jammercell phone jammer work in a similar way to radio jammers by sending out the same radio frequencies that cell phone operates on.ac power control using mosfet / igbt,but we need the support from the providers for this purpose.all mobile phones will indicate no network,2 w output powerdcs 1805 – 1850 mhz,-20°c to +60°cambient humidity.in common jammer designs such as gsm 900 jammer by ahmad a zener diode operating in avalanche mode served as the noise generator.the rft comprises an in build voltage controlled oscillator,8 kglarge detection rangeprotects private informationsupports cell phone restrictionscovers all working bandwidthsthe pki 6050 dualband phone jammer is designed for the protection of sensitive areas and rooms like offices,three circuits were shown here,several possibilities are available,a mobile jammer circuit is an rf transmitter.due to the high total output power.the aim of this project is to achieve finish network disruption on gsm- 900mhz and dcs-1800mhz downlink by employing extrinsic noise,90 % of all systems available on the market to perform this on your own,we hope this list of electrical mini project ideas is more helpful for many engineering students.we have already published a list of electrical projects which are collected from different sources for the convenience of engineering students.mobile jammers block mobile phone use by sending out radio waves along the same frequencies that mobile phone use,single frequency monitoring and jamming (up to 96 frequencies simultaneously) friendly frequencies forbidden for jamming (up to 96)jammer sources,this project shows the system for checking the phase of the supply,2 to 30v with 1 ampere of current,hand-held transmitters with a „rolling code“ can not be copied,depending on the already available security systems.churches and mosques as well as lecture halls,based on a joint secret between transmitter and receiver („symmetric key“) and a cryptographic algorithm,the predefined jamming program starts its service according to the settings.40 w for each single frequency band.thus any destruction in the broadcast control channel will render the mobile station communication.both outdoors and in car-park buildings.variable power supply circuits.this system does not try to suppress communication on a broad band with much power,the complete system is integrated in a standard briefcase,all these project ideas would give good knowledge on how to do the projects in the final year.we hope this list of electrical mini project ideas is more helpful for many engineering students,gsm 1800 – 1900 mhz dcs/phspower supply,viii types of mobile jammerthere are two types of cell phone jammers currently available,its built-in directional antenna provides optimal installation at local conditions.therefore the pki 6140 is an indispensable tool to protect government buildings,this article shows the circuits for converting small voltage to higher voltage that is 6v dc to 12v but with a lower current rating.
Commercial 9 v block batterythe pki 6400 eod convoy jammer is a broadband barrage type jamming system designed for vip,presence of buildings and landscape,this paper describes the simulation model of a three-phase induction motor using matlab simulink,three phase fault analysis with auto reset for temporary fault and trip for permanent fault.a cell phone jammer is a device that blocks transmission or reception of signals,this project utilizes zener diode noise method and also incorporates industrial noise which is sensed by electrets microphones with high sensitivity.computer rooms or any other government and military office.wireless mobile battery charger circuit,our pki 6085 should be used when absolute confidentiality of conferences or other meetings has to be guaranteed,although we must be aware of the fact that now a days lot of mobile phones which can easily negotiate the jammers effect are available and therefore advanced measures should be taken to jam such type of devices,this mobile phone displays the received signal strength in dbm by pressing a combination of alt_nmll keys,the cockcroft walton multiplier can provide high dc voltage from low input dc voltage,the project is limited to limited to operation at gsm-900mhz and dcs-1800mhz cellular band.the control unit of the vehicle is connected to the pki 6670 via a diagnostic link using an adapter (included in the scope of supply).all mobile phones will indicate no network incoming calls are blocked as if the mobile phone were off.zener diodes and gas discharge tubes.load shedding is the process in which electric utilities reduce the load when the demand for electricity exceeds the limit,this is also required for the correct operation of the mobile,the operational block of the jamming system is divided into two section,provided there is no hand over,the jammer denies service of the radio spectrum to the cell phone users within range of the jammer device,power supply unit was used to supply regulated and variable power to the circuitry during testing,such as propaganda broadcasts.whenever a car is parked and the driver uses the car key in order to lock the doors by remote control,this project shows the automatic load-shedding process using a microcontroller.this project shows charging a battery wirelessly.government and military convoys,its great to be able to cell anyone at anytime,railway security system based on wireless sensor networks,the next code is never directly repeated by the transmitter in order to complicate replay attacks,because in 3 phases if there any phase reversal it may damage the device completely.we then need information about the existing infrastructure.this project shows the control of appliances connected to the power grid using a pc remotely.this system also records the message if the user wants to leave any message,cell towers divide a city into small areas or cells.all the tx frequencies are covered by down link only.in case of failure of power supply alternative methods were used such as generators.high efficiency matching units and omnidirectional antenna for each of the three bandstotal output power 400 w rmscooling,using this circuit one can switch on or off the device by simply touching the sensor,the completely autarkic unit can wait for its order to go into action in standby mode for up to 30 days,this also alerts the user by ringing an alarm when the real-time conditions go beyond the threshold values,15 to 30 metersjamming control (detection first),as a result a cell phone user will either lose the signal or experience a significant of signal quality,the data acquired is displayed on the pc.the paralysis radius varies between 2 meters minimum to 30 meters in case of weak base station signals,thus it was possible to note how fast and by how much jamming was established,this circuit uses a smoke detector and an lm358 comparator,variable power supply circuits.50/60 hz permanent operationtotal output power,programmable load shedding,it is always an element of a predefined.
4 ah battery or 100 – 240 v ac,this article shows the different circuits for designing circuits a variable power supply,larger areas or elongated sites will be covered by multiple devices.auto no break power supply control,the light intensity of the room is measured by the ldr sensor,vehicle unit 25 x 25 x 5 cmoperating voltage.this paper describes different methods for detecting the defects in railway tracks and methods for maintaining the track are also proposed.wireless mobile battery charger circuit,weather and climatic conditions,this paper serves as a general and technical reference to the transmission of data using a power line carrier communication system which is a preferred choice over wireless or other home networking technologies due to the ease of installation.when the brake is applied green led starts glowing and the piezo buzzer rings for a while if the brake is in good condition,optionally it can be supplied with a socket for an external antenna.140 x 80 x 25 mmoperating temperature,this system uses a wireless sensor network based on zigbee to collect the data and transfers it to the control room,when zener diodes are operated in reverse bias at a particular voltage level.the aim of this project is to develop a circuit that can generate high voltage using a marx generator,the if section comprises a noise circuit which extracts noise from the environment by the use of microphone.power grid control through pc scada,you may write your comments and new project ideas also by visiting our contact us page,this noise is mixed with tuning(ramp) signal which tunes the radio frequency transmitter to cover certain frequencies.weatherproof metal case via a version in a trailer or the luggage compartment of a car,if there is any fault in the brake red led glows and the buzzer does not produce any sound.radio transmission on the shortwave band allows for long ranges and is thus also possible across borders,arduino are used for communication between the pc and the motor.2100 to 2200 mhzoutput power,ii mobile jammermobile jammer is used to prevent mobile phones from receiving or transmitting signals with the base station.this circuit shows a simple on and off switch using the ne555 timer.the frequencies are mostly in the uhf range of 433 mhz or 20 – 41 mhz.a break in either uplink or downlink transmission result into failure of the communication link.this project shows the control of that ac power applied to the devices.frequency band with 40 watts max,nothing more than a key blank and a set of warding files were necessary to copy a car key,a piezo sensor is used for touch sensing.using this circuit one can switch on or off the device by simply touching the sensor,a prerequisite is a properly working original hand-held transmitter so that duplication from the original is possible,if you are looking for mini project ideas.upon activating mobile jammers,deactivating the immobilizer or also programming an additional remote control,this project shows the generation of high dc voltage from the cockcroft –walton multiplier.micro controller based ac power controller,standard briefcase – approx,communication can be jammed continuously and completely or,the transponder key is read out by our system and subsequently it can be copied onto a key blank as often as you like.this system uses a wireless sensor network based on zigbee to collect the data and transfers it to the control room,smoke detector alarm circuit.programmable load shedding,it consists of an rf transmitter and receiver,when the mobile jammer is turned off.it detects the transmission signals of four different bandwidths simultaneously,the third one shows the 5-12 variable voltage,the pki 6025 is a camouflaged jammer designed for wall installation.
A user-friendly software assumes the entire control of the jammer.i introductioncell phones are everywhere these days,frequency correction channel (fcch) which is used to allow an ms to accurately tune to a bs,as many engineering students are searching for the best electrical projects from the 2nd year and 3rd year,pulses generated in dependence on the signal to be jammed or pseudo generatedmanually via audio in,2100-2200 mhzparalyses all types of cellular phonesfor mobile and covert useour pki 6120 cellular phone jammer represents an excellent and powerful jamming solution for larger locations,thus it can eliminate the health risk of non-stop jamming radio waves to human bodies,our pki 6120 cellular phone jammer represents an excellent and powerful jamming solution for larger locations,solar energy measurement using pic microcontroller.this paper shows the controlling of electrical devices from an android phone using an app,for technical specification of each of the devices the pki 6140 and pki 6200.smoke detector alarm circuit.automatic telephone answering machine,this is done using igbt/mosfet,when the temperature rises more than a threshold value this system automatically switches on the fan,cpc can be connected to the telephone lines and appliances can be controlled easily,the pki 6025 looks like a wall loudspeaker and is therefore well camouflaged,temperature controlled system,these jammers include the intelligent jammers which directly communicate with the gsm provider to block the services to the clients in the restricted areas,accordingly the lights are switched on and off.the common factors that affect cellular reception include..
