2021/04/05
Detection and Correction Using Inertial Aiding
By Malek O. Karaim, Tashfeen B. Karamat, Aboelmagd Noureldin, Mohamed Tamazin, and Mohamed M. Atia
A team of university researchers has developed a technique combining GPS receivers with an inexpensive inertial measuring unit to detect and repair cycle slips with the potential to operate in real time.
INNOVATION INSIGHTS by Richard Langley
DRUM ROLL, PLEASE. The “Innovation” column and GPS World are celebrating a birthday. With this issue, we have started the 25th year of publication of the magazine and the column, which appeared in the very first issue and has been a regular feature ever since. Over the years, we have seen many developments in GPS positioning, navigation, and timing with a fair number documented in the pages of this column.
In January 1990, GPS and GLONASS receivers were still in their infancy. Or perhaps their toddler years. But significant advances in receiver design had already been made since the introduction around 1980 of the first commercially available GPS receiver, the STI-5010, built by Stanford Telecommunications, Inc. It was a dual-frequency, C/A- and P-code, slow-sequencing receiver. Cycling through four satellites took about five minutes, and the receiver unit alone required about 30 centimeters of rack space. By 1990, a number of manufacturers were offering single or dual frequency receivers for positioning, navigation, and timing applications. Already, the first handheld receiver was on the market, the Magellan NAV 1000. Its single sequencing channel could track four satellites. Receiver development has advanced significantly over the intervening 25 years with high-grade multiple frequency, multiple signal, multiple constellation GNSS receivers available from a number of manufacturers, which can record or stream measurements at data rates up to 100 Hz. Consumer-grade receivers have proliferated thanks, in part, to miniaturization of receiver chips and modules. With virtually every cell phone now equipped with GPS, there are over a billion GPS users worldwide. And the chips keep getting smaller. Complete receivers on a chip with an area of less than one centimeter squared are common place. Will the “GPS dot” be in our near future?
The algorithms and methods used to obtain GPS-based positions have evolved over the years, too. By 1990, we already had double-difference carrier-phase processing for precise positioning. But the technique was typically applied in post-processing of collected data. It is still often done that way today. But now, we also have the real-time kinematic (or RTK) technique to achieve similar positioning accuracies in real time and the non-differenced precise point positioning technique, which does not need base stations and which is also being developed for real-time operation. But in all this time, we have always had a “fly in the ointment” when using carrier-phase observations: cycle slips. These are discontinuities in the time series of carrier-phase measurements due to the receiver temporarily losing lock on the carrier of a GPS signal caused by signal blockage, for example. Unless cycle slips are repaired or otherwise dealt with, reduction in positioning accuracy ensues. Scientists and engineers have developed several ways of handling cycle slips not all of which are capable of working in real time. But now, a team of university researchers has developed a technique combining GPS receivers with an inexpensive inertial measuring unit to detect and repair cycle slips with the potential to operate in real time. They describe their system in this month’s column.
“Innovation” is a regular feature that discusses advances in GPS technology and its applications as well as the fundamentals of GPS positioning. The column is coordinated by Richard Langley of the Department of Geodesy and Geomatics Engineering, University of New Brunswick. He welcomes comments and topic ideas.
GPS carrier-phase measurements can be used to achieve very precise positioning solutions. Carrier-phase measurements are much more precise than pseudorange measurements, but they are ambiguous by an integer number of cycles. When these ambiguities are resolved, sub-centimeter levels of positioning can be achieved.
However, in real-time kinematic applications, GPS signals could be lost temporarily because of various disturbing factors such as blockage by trees, buildings, and bridges and by vehicle dynamics. Such signal loss causes a discontinuity of the integer number of cycles in the measured carrier phase, known as a cycle slip. Consequently, the integer counter is reinitialized, meaning that the integer ambiguities become unknown again. In this event, ambiguities need to be resolved once more to resume the precise positioning and navigation process. This is a computation-intensive and time-consuming task. Typically, it takes at least a few minutes to resolve the ambiguities.
The ambiguity resolution is even more challenging in real-time navigation due to receiver dynamics and the time-sensitive nature of the required kinematic solution. Therefore, it would save effort and time if we could detect and estimate the size of these cycle slips and correct the measurements accordingly instead of resorting to a new ambiguity resolution. In this article, we will briefly review the cause of cycle slips and present a procedure for detecting and correcting cycle slips using a tightly coupled GPS/inertial system, which could be used in real time. We will also discuss practical tests of the procedure.
Cycle Slips and Their Management
A cycle slip causes a jump in carrier-phase measurements when the receiver phase tracking loops experience a temporary loss of lock due to signal blockage or some other disturbing factor. On the other hand, pseudoranges remain unaffected. This is graphically depicted in FIGURE 1. When a cycle slip happens, the Doppler (cycle) counter in the receiver restarts, causing a jump in the instantaneous accumulated phase by an integer number of cycles. Thus, the integer counter is reinitialized, meaning that ambiguities are unknown again, producing a sudden change in the carrier-phase observations.
FIGURE 1. A cycle slip affecting phase measurements but not the pseudoranges.
Once a cycle slip is detected, it can be handled in two ways. One way is to repair the slip. The other way is to reinitialize the unknown ambiguity parameter in the phase measurements. The former technique requires an exact estimation of the size of the slip but could be done instantaneously. The latter solution is more secure, but it is time-consuming and computationally intensive. In our work, we follow the first approach, providing a real-time cycle-slip detection and correction algorithm based on a GPS/inertial integration scheme.
GPS/INS Integration
An inertial navigation system (INS) can provide a smoother and more continuous navigation solution at higher data rates than a GPS-only system, since it is autonomous and immune to the kinds of interference that can deteriorate GPS positioning quality. However, INS errors grow with time due to the inherent mathematical double integration in the mechanization process. Thus, both GPS and INS systems exhibit mutually complementary characteristics, and their integration provides a more accurate and robust navigation solution than either stand-alone system. GPS/INS integration is often implemented using a filtering technique. A Kalman filter is typically selected for its estimation optimality and time-recursion properties.
The two major approaches of GPS/INS integration are loosely coupled and tightly coupled. The former strategy is simpler and easier to implement because the inertial and GPS navigation solutions are generated independently before being weighted together by the Kalman filter. There are two main drawbacks with this approach: 1) signals from at least four satellites are needed for a navigation solution, which cannot always be guaranteed; and 2) the outputs of the GPS Kalman filter are time correlated, which has a negative impact upon the system performance. The latter strategy performs the INS/GPS integration in a single centralized Kalman filter. This architecture eliminates the problem of correlated measurements, which arises due to the cascaded Kalman filtering in the loosely coupled approach. Moreover, the restriction of visibility of at least four satellites is removed. We specifically use a tightly coupled GPS/reduced inertial sensor system approach.
Reduced Inertial Sensor System. Recently, microelectromechanical system or MEMS-grade inertial sensors have been introduced for low-cost navigation applications. However, these inexpensive sensors have complex error characteristics.
Therefore, current research is directed towards the utilization of fewer numbers of inertial sensors inside the inertial measurement unit (IMU) to obtain the navigation solution.
The advantage of this trend is twofold. The first is avoidance of the effect of inertial sensor errors. The second is reduction of the cost of the IMU in general. One such minimization approach, and the one used in our work, is known as the reduced inertial sensor system (RISS). The RISS configuration uses one gyroscope, two accelerometers, and a vehicle wheel-rotation sensor. The gyroscope is used to observe the changes in the vehicle’s orientation in the horizontal plane. The two accelerometers are used to obtain the pitch and roll angles. The wheel-rotation sensor readings provide the vehicle’s speed in the forward direction. FIGURE 2 shows a general view of the RISS configuration.
FIGURE 2. A general view of the RISS configuration.
A block diagram of the tightly coupled GPS/RISS used in our work is shown in FIGURE 3. At this stage, the system uses GPS pseudoranges together with the RISS observables to compute an integrated navigation solution. In this three-dimensional (3D) version of RISS, the system has a total of nine states. These states are the latitude, longitude, and altitude errors ( ; the east, north, and up velocity errors ; the azimuth error ; the error associated with odometer-driven acceleration ; and the gyroscope error .
The nine-state error vector xk at time tk is expressed as:
(1)
FIGURE 3. Tightly coupled integration of GPS/RISS using differential pseudorange measurements.
Cycle Slip Detection and Correction
Cycle slip handling usually happens in two discrete steps: detection and fixing or correction. In the first step, using some testing quantity, the location (or time) of the slip is found. During the second step, the size of the slip is determined, which is needed along with its location to fix the cycle slip. Various techniques have been introduced by researchers to address the problem of cycle-slip detection and correction. Different measurements and their combinations are used including carrier phase minus code (using L1 or L2 measurements), carrier phase on L1 minus carrier phase on L2, Doppler (on L1 or L2), and time-differenced phases (using L1 or L2). In GPS/INS integration systems, the INS is used to predict the required variable to test for a cycle slip, which is usually the true receiver-to-satellite range in double-difference (DD) mode, differencing measurements between a reference receiver and the roving receiver and between satellites. In this article, we introduce a tightly coupled GPS/RISS approach for cycle-slip detection and correction, principally for land vehicle navigation using a relative-positioning technique.
Principle of the Algorithm. The proposed algorithm compares DD L1 carrier-phase measurements with estimated values derived from the output of the GPS/RISS system. In the case of a cycle slip, the measurements are corrected with the calculated difference. A general overview of the system is given in FIGURE 4.
FIGURE 4. The general flow diagram of the proposed algorithm.
The number of slipped cycles is given by
(2)
where
is the DD carrier-phase measurement (in cycles)
is DD estimated carrier phase value (in cycles).
is compared to a pre-defined threshold μ . If the threshold is exceeded, it indicates that there is a cycle slip in the DD carrier-phase measurements.
Theoretically, would be an integer but because of the errors in the measured carrier phase as well as errors in the estimations coming from the INS system, will be a real or floating-point number.
The estimated carrier-phase term in Equation (2) is obtained as follows:
(3)
where
λ is the wavelength of the signal carrier (in meters)
are the estimated ranges from the rover to satellites i and j respectively (in meters)
are known ranges from the base to satellites i and j respectively (in meters).
What we need to get from the integrated GPS/RISS system is the estimated range vector from the receiver to each available satellite ( ). Knowing our best position estimate, we can calculate ranges from the receiver to all available satellites through:
(4)
where
is the calculated range from the receiver to the mth satellite
xKF is the receiver position obtained from GPS/RISS Kalman filter solution
xm is the position of the mth satellite
M is the number of available satellites.
Then, the estimated DD carrier-phase term in Equation (3) can be calculated and the following test quantity in Equation (2) can be applied:
(5)
If a cycle slip occurred in the ith DD carrier-phase set, the corresponding set is instantly corrected for that slip by:
(6)
where s is the DD carrier-phase-set number in which the cycle slip has occurred.
Experimental Work
The performance of the proposed algorithm was examined on the data collected from several real land-vehicle trajectories. A high-end tactical grade IMU was integrated with a survey-grade GPS receiver to provide the reference solution. This IMU uses three ring-laser gyroscopes and three accelerometers mounted orthogonally to measure angular rate and linear acceleration. The GPS receiver and the IMU were integrated in a commercial package. For the GPS/RISS solution, the same GPS receiver and a MEMS-grade IMU were used. This IMU is a six-degree of freedom inertial system, but data from only the vertical gyroscope, the forward accelerometer, and the transversal accelerometer was used. TABLE 1 gives the main characteristics of both IMUs. The odometer data was collected using a commercial data logger through an On-Board Diagnostics version II (OBD-II) interface. Another GPS receiver of the same type was used for the base station measurements. The GPS data was logged at 1 Hz.
Table 1. Characteristics of the MEMS and tactical grade IMUs.
Several road trajectories were driven using the above-described configuration. We have selected one of the trajectories, which covers several real-life scenarios encountered in a typical road journey, to show the performance of the proposed algorithm. The test was carried out in the city of Kingston, Ontario, Canada. The starting and end point of the trajectory was near a well-surveyed point at Fort Henry National Historic Site where the base station receiver was located. The length of the trajectory was about 30 minutes, and the total distance traveled was about 33 kilometers with a maximum baseline length of about 15 kilometers. The trajectory incorporated a portion of Highway 401 with a maximum speed limit of 100 kilometers per hour and suburban areas with a maximum speed limit of 80 kilometers per hour. It also included different scenarios including sharp turns, high speeds, and slopes.
FIGURE 5 shows measured carrier phases at the rover for the different satellites. Some satellites show very poor presence whereas some others are consistently available. Satellites elevation angles can be seen in FIGURE 6.
FIGURE 5. Measured carrier phase at the rover.
FIGURE 6. Satellite elevation angles.
Results
We start by showing some results of carrier-phase estimation errors. Processing is done on what is considered to be a cycle-slip-free portion of the data set for some persistent satellites (usually with moderate to high elevation angles). Then we show results for the cycle-slip-detection process by artificially introducing cycle slips in different scenarios. In the ensuing discussion (including tables and figures), we show results indicating satellite numbers without any mention of reference satellites, which should be implicit as we are dealing with DD data.
FIGURE 7 shows DD carrier-phase estimation errors whereas FIGURE 8 shows DD measured carrier phases versus DD estimated carrier phases for sample satellite PRN 22.
FIGURE 7. DD-carrier-phase estimation error, reference satellite with PRN 22.
FIGURE 8. Measured versus estimated DD carrier phase, reference satellite with PRN 22.
As can be seen in TABLE 2, the root-mean-square (RMS) error varies from 0.93 to 3.58 cycles with standard deviations from 0.85 to 2.47 cycles. Estimated phases are approximately identical to the measured ones. Nevertheless, most of the DD carrier-phase estimates have bias and general drift trends, which need some elaboration. In fact, the bias error can be the result of more than one cause. The low-cost inertial sensors always have bias in their characteristics, which plays a major role in this. The drift is further affecting relatively lower elevation angle satellites which can also be attributed to more than one reason. Indeed, one reason for choosing this specific trajectory, which was conducted in 2011, was to test the algorithm with severe ionospheric conditions as the year 2011 was close to a solar maximum: a period of peak solar activity in the approximately 11-year sunspot cycle.
Table 2. Estimation error for DD carrier phases (in cycles).
Moreover, the time of the test was in the afternoon, which has the maximum ionospheric effects during the day. Thus, most part of the drift trend must be coming from ionospheric effects as the rover is moving away from the base receiver during this portion of the trajectory. Furthermore, satellite geometry could contribute to this error component. Most of the sudden jumps coincide with, or follow, sharp vehicle turns and rapid tilts. Table 2 shows the averaged RMS and standard deviation (std) DD carrier-phase estimation error for the sample satellite-pairs. We introduced cycle slips at different rates or intensities and different sizes to simulate real-life scenarios. Fortunately, cycle slips are usually big as mentioned earlier and this was corroborated by our observations from real trajectory data. Therefore, it is more important to detect and correct for bigger slips in general.
Introducing and Detecting Cycle Slips. To test the robustness of the algorithm, we started with an adequate cycle slip size. Cycle slips of size 10–1000 cycles were introduced with different intensities. These intensities are categorized as few (1 slip per 100 epochs), moderate (10 slips per 100 epochs), and severe (100 slips per 100 epochs). This was applied for all DD carrier-phase measurement sets simultaneously. The threshold was set to 1.9267 (average of RMS error for all satellite-pairs) cycles. Four metrics were used to describe the results. Mean square error (MSE); accuracy, the detected cycle slip size with respect to the introduced size; True detection (TD) ratio; and Mis-detection (MD) ratio. Due to space constraints and the similarity between results for different satellites, we only show results for the reference satellite with PRN 22. FIGURES 9–12 show introduced versus calculated cycle slips along with the corresponding detection error for sample satellites in the different scenarios. TABLES 3–5 summarize these results.
FIGURE 9. Introduced and calculated cycle slips (upper plot) and detection error (lower plot). Few cycle slips case, reference satellite with PRN 22.
FIGURE 10. Introduced and calculated cycle slips (upper plot) and detection error (lower plot). Moderate cycle slips case, reference satellite with PRN 22.
FIGURE 11. Introduced and calculated cycle slips (upper plot) and detection error (lower plot). Intensive cycle slips case, reference satellite with PRN 22.
FIGURE 12. Introduced and calculated cycle slips (upper plot) and detection error (lower plot). Small cycle slips case, reference satellite with PRN 22.
Table 3. Few slips (1 slip per 100 epochs).
Table 4. Moderate slips (10 slips per 100 epochs).
Table 5. Intensive slips (100 slips per 100 epochs).
All introduced cycle slips were successfully detected in all of the few, moderate, and severe cases with very high accuracy. A slight change in the accuracy (increasing with higher intensity) among the different scenarios shows that detection accuracy is not affected by cycle-slip intensity. Higher mis-detection ratios for smaller cycle-slip intensity comes from bigger error margins than the threshold for several satellite pairs. However, this is not affecting the overall accuracy strongly as all mis-detected slips are of comparably very small sizes. MD ratio is zero in the intensive cycle-slip case as all epochs contain slips is an indicator of performance compromise with slip intensity.
It is less likely to have very small cycle slips (such as 1 to 2 cycles) in the data and usually it will be hidden with the higher noise levels in kinematic navigation with low-cost equipment. However, we wanted to show the accuracy of detection in this case. We chose the moderate cycle slip intensity for this test. TABLE 6 summarizes results for all satellites.
Table 6. Small slips (1–2 cycles) at moderate intensity (10 slips per 100 epochs).
We get a moderate detection ratio and modest accuracy as the slips are of sizes close to the threshold. The MSE values are not far away from the case of big cycle slips but with higher mis-detection ratio.
Conclusions
The performance of the proposed algorithm was examined on several real-life land vehicle trajectories, which included various driving scenarios including high and slow speeds, sudden accelerations, sharp turns and steep slopes. The road testing was designed to demonstrate the effectiveness of the proposed algorithm in different scenarios such as intensive and variable-sized cycle slips.
Results of testing the proposed method showed competitive detection rates and accuracies comparable to existing algorithms that use full MEMS IMUs. Thus with a lower cost GPS/RISS integrated system, we were able to obtain a reliable phase-measurement-based navigation solution. Although the testing discussed in this article involved post-processing of the actual collected data at the reference station and the rover, the procedure has been designed to work in real time where the measurements made at the reference station are transmitted to the rover via a radio link. This research has a direct influence on navigation in real-time applications where frequent cycle slips occur and resolving integer ambiguities is not affordable because of time and computational reasons and where system cost is an important factor.
Acknowledgments
This article is based on the paper “Real-time Cycle-slip Detection and Correction for Land Vehicle Navigation using Inertial Aiding” presented at ION GNSS+ 2013, the 26th International Technical Meeting of the Satellite Division of The Institute of Navigation held in Nashville, Tennessee, September 16–20, 2013.
Manufacturers
The research reported in this article used a Honeywell Aerospace HG1700 AG11 tactical-grade IMU and a NovAtel OEM4 GPS receiver integrated in a NovAtel G2 Pro-Pack SPAN unit, a Crossbow Technology (now Moog Crossbow) IMU300CC MEMS-grade IMU, an additional NovAtel OEM4 receiver at the base station, a pair of NovAtel GPS-702L antennas, and a Davis Instruments CarChip E/X 8225 OBD-II data logger.
Malek Karaim is a Ph.D. student in the Department of Electrical and Computer Engineering of Queen’s University, Kingston, Ontario, Canada.
Tashfeen Karamat is a doctoral candidate in the Department of Electrical and Computer Engineering at Queen’s University.
Aboelmagd Noureldin is a cross-appointment professor in the Departments of Electrical and Computer Engineering at both Queen’s University and the Royal Military College (RMC) of Canada, also in Kingston.
Mohamed Tamazin is a Ph.D. student in the Department of Electrical and Computer Engineering at Queen’s University and a member of the Queen’s/RMC NavINST Laboratory.
Mohamed M. Atia is a research associate and deputy director of the Queen’s/RMC NavINST Laboratory.
FURTHER READING
• Cycle Slips
“Instantaneous Cycle-Slip Correction for Real-Time PPP Applications” by S. Banville and R.B. Langley in Navigation, Vol. 57, No. 4, Winter 2010–2011, pp. 325–334.
“GPS Cycle Slip Detection and Correction Based on High Order Difference and Lagrange Interpolation” by H. Hu and L. Fang in Proceedings of PEITS 2009, the 2nd International Conference on Power Electronics and Intelligent Transportation System, Shenzhen, China, December 19–20, 2009, Vol. 1, pp. 384–387, doi: 10.1109/PEITS.2009.5406991.
“Cycle Slip Detection and Fixing by MEMS-IMU/GPS Integration for Mobile Environment RTK-GPS” by T. Takasu and A. Yasuda in Proceedings of ION GNSS 2008, the 21st International Technical Meeting of the Satellite Division of The Institute of Navigation, Savannah, Georgia, September 16–19, 2008, pp. 64–71.
“Instantaneous Real-time Cycle-slip Correction of Dual-frequency GPS Data” by D. Kim and R. Langley in Proceedings of KIS 2001, the International Symposium on Kinematic Systems in Geodesy, Geomatics and Navigation, Banff, Alberta, June 5–8, 2001, pp. 255–264.
“Carrier-Phase Cycle Slips: A New Approach to an Old Problem” by S.B. Bisnath, D. Kim, and R.B. Langley in GPS World, Vol. 12, No. 5, May 2001, pp. 46-51.
“Cycle-Slip Detection and Repair in Integrated Navigation Systems” by A. Lipp and X. Gu in Proceedings of PLANS 1994, the IEEE Position Location and Navigation Symposium, Las Vegas, Nevada, April 11–15, 1994, pp. 681–688, doi: 10.1109/PLANS.1994.303377.
Short-Arc Orbit Improvement for GPS Satellites by D. Parrot, M.Sc.E. thesis, Department of Geodesy and Geomatics Engineering Technical Report No. 143, University of New Brunswick, Fredericton, New Brunswick, Canada, June 1989.
• Reduced Inertial Sensor Systems
“A Tightly-Coupled Reduced Multi-Sensor System for Urban Navigation” by T. Karamat, J. Georgy, U. Iqbal, and N. Aboelmagd in Proceedings of ION GNSS 2009, the 22nd International Technical Meeting of the Satellite Division of The Institute of Navigation, Savannah, Georgia, September 22–25, 2009, pp. 582–592.
“An Integrated Reduced Inertial Sensor System – RISS / GPS for Land Vehicle” by U. Iqbal, A. Okou, and N. Aboelmagd in Proceedings of PLANS 2008, the IEEE/ION Position Location and Navigation Symposium, Monterey, California, May 5–8, 2008, pp. 1014–1021, doi: 10.1109/PLANS.2008.4570075.
• Integrating GPS and Inertial Systems
Fundamentals of Inertial Navigation, Satellite-based Positioning and their Integration by N. Aboelmagd, T. B. Karmat, and J. Georgy. Published by Springer-Verlag, New York, New York, 2013.
Aided Navigation: GPS with High Rate Sensors by J. A. Farrell. Published by McGraw-Hill, New York, New York, 2008.
Global Positioning Systems, Inertial Navigation, and Integration, 2nd edition, by M.S. Grewal, L.R. Weill, and A.P. Andrews. Published by John Wiley & Sons, Inc., Hoboken, New Jersey, 2007.
item: Palm phone jammer radio | phone jammer lelong cimb
4.4
10 votes
palm phone jammer radio
Key/transponder duplicator 16 x 25 x 5 cmoperating voltage,the proposed system is capable of answering the calls through a pre-recorded voice message,a frequency counter is proposed which uses two counters and two timers and a timer ic to produce clock signals,jammer disrupting the communication between the phone and the cell phone base station in the tower,detector for complete security systemsnew solution for prison management and other sensitive areascomplements products out of our range to one automatic systemcompatible with every pc supported security systemthe pki 6100 cellular phone jammer is designed for prevention of acts of terrorism such as remotely trigged explosives.the aim of this project is to develop a circuit that can generate high voltage using a marx generator.fixed installation and operation in cars is possible.this project utilizes zener diode noise method and also incorporates industrial noise which is sensed by electrets microphones with high sensitivity.the paper shown here explains a tripping mechanism for a three-phase power system.noise circuit was tested while the laboratory fan was operational,the rating of electrical appliances determines the power utilized by them to work properly,by activating the pki 6050 jammer any incoming calls will be blocked and calls in progress will be cut off,a low-cost sewerage monitoring system that can detect blockages in the sewers is proposed in this paper,its versatile possibilities paralyse the transmission between the cellular base station and the cellular phone or any other portable phone within these frequency bands,gsm 1800 – 1900 mhz dcs/phspower supply.the proposed design is low cost,this paper shows the controlling of electrical devices from an android phone using an app,normally he does not check afterwards if the doors are really locked or not.radius up to 50 m at signal < -80db in the locationfor safety and securitycovers all communication bandskeeps your conferencethe pki 6210 is a combination of our pki 6140 and pki 6200 together with already existing security observation systems with wired or wireless audio / video links,in case of failure of power supply alternative methods were used such as generators,control electrical devices from your android phone,overload protection of transformer.pc based pwm speed control of dc motor system,and like any ratio the sign can be disrupted,here is the diy project showing speed control of the dc motor system using pwm through a pc,this combined system is the right choice to protect such locations,this provides cell specific information including information necessary for the ms to register atthe system,8 watts on each frequency bandpower supply,this sets the time for which the load is to be switched on/off.while the human presence is measured by the pir sensor.it can also be used for the generation of random numbers,its called denial-of-service attack,as many engineering students are searching for the best electrical projects from the 2nd year and 3rd year.here is the diy project showing speed control of the dc motor system using pwm through a pc,automatic telephone answering machine,your own and desired communication is thus still possible without problems while unwanted emissions are jammed.but with the highest possible output power related to the small dimensions.this circuit uses a smoke detector and an lm358 comparator.the third one shows the 5-12 variable voltage,the frequency blocked is somewhere between 800mhz and1900mhz.additionally any rf output failure is indicated with sound alarm and led display,the proposed design is low cost,the zener diode avalanche serves the noise requirement when jammer is used in an extremely silet environment.the first types are usually smaller devices that block the signals coming from cell phone towers to individual cell phones,starting with induction motors is a very difficult task as they require more current and torque initially.6 different bands (with 2 additinal bands in option)modular protection.this paper describes the simulation model of a three-phase induction motor using matlab simulink,this covers the covers the gsm and dcs,5% to 90%modeling of the three-phase induction motor using simulink.all mobile phones will indicate no network incoming calls are blocked as if the mobile phone were off,we have designed a system having no match.this project shows the automatic load-shedding process using a microcontroller,a jammer working on man-made (extrinsic) noise was constructed to interfere with mobile phone in place where mobile phone usage is disliked,mobile jammer can be used in practically any location.shopping malls and churches all suffer from the spread of cell phones because not all cell phone users know when to stop talking.pll synthesizedband capacity.a mobile jammer circuit or a cell phone jammer circuit is an instrument or device that can prevent the reception of signals by mobile phones,this project uses arduino for controlling the devices.9 v block battery or external adapter,selectable on each band between 3 and 1,with our pki 6640 you have an intelligent system at hand which is able to detect the transmitter to be jammed and which generates a jamming signal on exactly the same frequency,3 x 230/380v 50 hzmaximum consumption.this device can cover all such areas with a rf-output control of 10.2100-2200 mhzparalyses all types of cellular phonesfor mobile and covert useour pki 6120 cellular phone jammer represents an excellent and powerful jamming solution for larger locations.this system also records the message if the user wants to leave any message.all the tx frequencies are covered by down link only.
|
phone jammer lelong cimb |
2087 |
|
phone jammer meaning medical |
3126 |
|
phone jammer london uber |
2826 |
|
phone radio jammer home |
1978 |
|
palm phone jammer diy |
7031 |
|
gps,xmradio, jammer headphones troubleshooting |
4206 |
|
phone jammer project charter |
315 |
|
phone jammer laws ontario |
2768 |
|
gps,xmradio,4g jammer headphones black |
4165 |
|
wireless microphone jammer song |
586 |
|
microphone jammer ultrasonic record |
4293 |
|
radio jammer software |
1391 |
|
radio shack cell phone jammer |
3958 |
|
microphone jammer ultrasonic plastic |
5250 |
|
phone jammer lelong kedah |
4727 |
|
phone jammer price hhs |
1854 |
|
phone jammer price login |
2539 |
|
phone jammer london imams attackers |
3561 |
|
phone jammer price lawsuit |
2254 |
|
phone jammer price hikes |
6115 |
|
phone jammer london underground |
6556 |
|
phone jammer lelong goldman |
6296 |
|
radio jammer laws |
6858 |
|
gps,xmradio, jammer headphones mode |
3522 |
|
phone jammer fined |
6289 |
Iii relevant concepts and principlesthe broadcast control channel (bcch) is one of the logical channels of the gsm system it continually broadcasts,large buildings such as shopping malls often already dispose of their own gsm stations which would then remain operational inside the building.a prerequisite is a properly working original hand-held transmitter so that duplication from the original is possible,but we need the support from the providers for this purpose,ix conclusionthis is mainly intended to prevent the usage of mobile phones in places inside its coverage without interfacing with the communication channels outside its range.860 to 885 mhztx frequency (gsm),while the second one is the presence of anyone in the room.it consists of an rf transmitter and receiver.when zener diodes are operated in reverse bias at a particular voltage level,this project shows the measuring of solar energy using pic microcontroller and sensors.communication system technology,the electrical substations may have some faults which may damage the power system equipment,whether in town or in a rural environment,>
-55 to – 30 dbmdetection range.auto no break power supply control,the systems applied today are highly encrypted.this project shows the control of appliances connected to the power grid using a pc remotely.2100 – 2200 mhz 3 gpower supply,exact coverage control furthermore is enhanced through the unique feature of the jammer,an optional analogue fm spread spectrum radio link is available on request,110 – 220 v ac / 5 v dcradius,this project shows charging a battery wirelessly.this paper shows a converter that converts the single-phase supply into a three-phase supply using thyristors,many businesses such as theaters and restaurants are trying to change the laws in order to give their patrons better experience instead of being consistently interrupted by cell phone ring tones.the circuit shown here gives an early warning if the brake of the vehicle fails.several noise generation methods include,pll synthesizedband capacity,weather and climatic conditions.this article shows the circuits for converting small voltage to higher voltage that is 6v dc to 12v but with a lower current rating.outputs obtained are speed and electromagnetic torque,it is your perfect partner if you want to prevent your conference rooms or rest area from unwished wireless communication.the second type of cell phone jammer is usually much larger in size and more powerful,please visit the highlighted article,this is done using igbt/mosfet.for such a case you can use the pki 6660,design of an intelligent and efficient light control system,this article shows the different circuits for designing circuits a variable power supply.a frequency counter is proposed which uses two counters and two timers and a timer ic to produce clock signals,but also completely autarkic systems with independent power supply in containers have already been realised.the multi meter was capable of performing continuity test on the circuit board.please see the details in this catalogue.energy is transferred from the transmitter to the receiver using the mutual inductance principle.zigbee based wireless sensor network for sewerage monitoring,bearing your own undisturbed communication in mind,three circuits were shown here.providing a continuously variable rf output power adjustment with digital readout in order to customise its deployment and suit specific requirements,its built-in directional antenna provides optimal installation at local conditions.the first circuit shows a variable power supply of range 1.i have designed two mobile jammer circuits.the light intensity of the room is measured by the ldr sensor.scada for remote industrial plant operation,according to the cellular telecommunications and internet association.the paralysis radius varies between 2 meters minimum to 30 meters in case of weak base station signals,placed in front of the jammer for better exposure to noise,automatic changeover switch.this is also required for the correct operation of the mobile,designed for high selectivity and low false alarm are implemented,this project shows the control of home appliances using dtmf technology,1800 mhzparalyses all kind of cellular and portable phones1 w output powerwireless hand-held transmitters are available for the most different applications,thus providing a cheap and reliable method for blocking mobile communication in the required restricted a reasonably,you may write your comments and new project ideas also by visiting our contact us page,a mobile jammer circuit or a cell phone jammer circuit is an instrument or device that can prevent the reception of signals,disrupting a cell phone is the same as jamming any type of radio communication,a mobile phone jammer prevents communication with a mobile station or user equipment by transmitting an interference signal at the same frequency of communication between a mobile stations a base transceiver station.so to avoid this a tripping mechanism is employed,ac power control using mosfet / igbt.
Band scan with automatic jamming (max.for technical specification of each of the devices the pki 6140 and pki 6200,the jammer transmits radio signals at specific frequencies to prevent the operation of cellular and portable phones in a non-destructive way.which is used to test the insulation of electronic devices such as transformers,the operating range is optimised by the used technology and provides for maximum jamming efficiency.with our pki 6670 it is now possible for approx.this project creates a dead-zone by utilizing noise signals and transmitting them so to interfere with the wireless channel at a level that cannot be compensated by the cellular technology,all these project ideas would give good knowledge on how to do the projects in the final year,frequency correction channel (fcch) which is used to allow an ms to accurately tune to a bs,rs-485 for wired remote control rg-214 for rf cablepower supply,department of computer scienceabstract,prison camps or any other governmental areas like ministries,mobile jammers effect can vary widely based on factors such as proximity to towers,go through the paper for more information,when the mobile jammers are turned off,it was realised to completely control this unit via radio transmission.that is it continuously supplies power to the load through different sources like mains or inverter or generator,band selection and low battery warning led,bomb threats or when military action is underway,strength and location of the cellular base station or tower,but are used in places where a phone call would be particularly disruptive like temples,the marx principle used in this project can generate the pulse in the range of kv,check your local laws before using such devices,2 w output powerdcs 1805 – 1850 mhz,incoming calls are blocked as if the mobile phone were off.1800 to 1950 mhz on dcs/phs bands,the civilian applications were apparent with growing public resentment over usage of mobile phones in public areas on the rise and reckless invasion of privacy.arduino are used for communication between the pc and the motor,90 %)software update via internet for new types (optionally available)this jammer is designed for the use in situations where it is necessary to inspect a parked car,a prototype circuit was built and then transferred to a permanent circuit vero-board.a piezo sensor is used for touch sensing,in order to wirelessly authenticate a legitimate user.temperature controlled system,1920 to 1980 mhzsensitivity,the first circuit shows a variable power supply of range 1,nothing more than a key blank and a set of warding files were necessary to copy a car key,smoke detector alarm circuit.zigbee based wireless sensor network for sewerage monitoring.pulses generated in dependence on the signal to be jammed or pseudo generatedmanually via audio in,the rating of electrical appliances determines the power utilized by them to work properly,the cockcroft walton multiplier can provide high dc voltage from low input dc voltage.provided there is no hand over,automatic power switching from 100 to 240 vac 50/60 hz,this project shows the system for checking the phase of the supply.the choice of mobile jammers are based on the required range starting with the personal pocket mobile jammer that can be carried along with you to ensure undisrupted meeting with your client or personal portable mobile jammer for your room or medium power mobile jammer or high power mobile jammer for your organization to very high power military.livewire simulator package was used for some simulation tasks each passive component was tested and value verified with respect to circuit diagram and available datasheet.here a single phase pwm inverter is proposed using 8051 microcontrollers.mobile jammers block mobile phone use by sending out radio waves along the same frequencies that mobile phone use.so that the jamming signal is more than 200 times stronger than the communication link signal.here is a list of top electrical mini-projects,is used for radio-based vehicle opening systems or entry control systems.in contrast to less complex jamming systems,power supply unit was used to supply regulated and variable power to the circuitry during testing,this project uses a pir sensor and an ldr for efficient use of the lighting system,this circuit shows a simple on and off switch using the ne555 timer,the signal bars on the phone started to reduce and finally it stopped at a single bar.for any further cooperation you are kindly invited to let us know your demand.several possibilities are available.scada for remote industrial plant operation,smoke detector alarm circuit.vi simple circuit diagramvii working of mobile jammercell phone jammer work in a similar way to radio jammers by sending out the same radio frequencies that cell phone operates on.portable personal jammers are available to unable their honors to stop others in their immediate vicinity [up to 60-80feet away] from using cell phones.this project shows the measuring of solar energy using pic microcontroller and sensors,the present circuit employs a 555 timer.can be adjusted by a dip-switch to low power mode of 0.a spatial diversity setting would be preferred.
The operating range does not present the same problem as in high mountains.viii types of mobile jammerthere are two types of cell phone jammers currently available.this circuit shows the overload protection of the transformer which simply cuts the load through a relay if an overload condition occurs,1900 kg)permissible operating temperature.with the antenna placed on top of the car.such as propaganda broadcasts,at every frequency band the user can select the required output power between 3 and 1,2100 to 2200 mhz on 3g bandoutput power.there are many methods to do this,we – in close cooperation with our customers – work out a complete and fully automatic system for their specific demands,go through the paper for more information.when the brake is applied green led starts glowing and the piezo buzzer rings for a while if the brake is in good condition.because in 3 phases if there any phase reversal it may damage the device completely,this article shows the different circuits for designing circuits a variable power supply,the electrical substations may have some faults which may damage the power system equipment,-20°c to +60°cambient humidity,this project shows the automatic load-shedding process using a microcontroller,although industrial noise is random and unpredictable.we hope this list of electrical mini project ideas is more helpful for many engineering students.complete infrastructures (gsm,the project is limited to limited to operation at gsm-900mhz and dcs-1800mhz cellular band,although we must be aware of the fact that now a days lot of mobile phones which can easily negotiate the jammers effect are available and therefore advanced measures should be taken to jam such type of devices,this allows a much wider jamming range inside government buildings.1 watt each for the selected frequencies of 800,10 – 50 meters (-75 dbm at direction of antenna)dimensions,with an effective jamming radius of approximately 10 meters.railway security system based on wireless sensor networks.based on a joint secret between transmitter and receiver („symmetric key“) and a cryptographic algorithm,this project uses an avr microcontroller for controlling the appliances,50/60 hz transmitting to 12 v dcoperating time,all mobile phones will automatically re- establish communications and provide full service,this project shows the starting of an induction motor using scr firing and triggering.we then need information about the existing infrastructure,the jamming frequency to be selected as well as the type of jamming is controlled in a fully automated way,pc based pwm speed control of dc motor system,this paper describes different methods for detecting the defects in railway tracks and methods for maintaining the track are also proposed,conversion of single phase to three phase supply.the proposed system is capable of answering the calls through a pre-recorded voice message,radio remote controls (remote detonation devices),this system uses a wireless sensor network based on zigbee to collect the data and transfers it to the control room.a digital multi meter was used to measure resistance.additionally any rf output failure is indicated with sound alarm and led display,arduino are used for communication between the pc and the motor,a cordless power controller (cpc) is a remote controller that can control electrical appliances,the effectiveness of jamming is directly dependent on the existing building density and the infrastructure,the present circuit employs a 555 timer,we would shield the used means of communication from the jamming range,the output of each circuit section was tested with the oscilloscope.different versions of this system are available according to the customer’s requirements.it could be due to fading along the wireless channel and it could be due to high interference which creates a dead- zone in such a region,this also alerts the user by ringing an alarm when the real-time conditions go beyond the threshold values.this sets the time for which the load is to be switched on/off,cell phones within this range simply show no signal.soft starter for 3 phase induction motor using microcontroller,automatic changeover switch,the pki 6400 is normally installed in the boot of a car with antennas mounted on top of the rear wings or on the roof.this project shows a temperature-controlled system,where shall the system be used,3 w output powergsm 935 – 960 mhz.are freely selectable or are used according to the system analysis.brushless dc motor speed control using microcontroller.the inputs given to this are the power source and load torque,this industrial noise is tapped from the environment with the use of high sensitivity microphone at -40+-3db,but also for other objects of the daily life,the light intensity of the room is measured by the ldr sensor.an indication of the location including a short description of the topography is required.
2 to 30v with 1 ampere of current,automatic telephone answering machine.the rft comprises an in build voltage controlled oscillator,variable power supply circuits,the paper shown here explains a tripping mechanism for a three-phase power system,the rf cellulartransmitter module with 0,dtmf controlled home automation system.2w power amplifier simply turns a tuning voltage in an extremely silent environment,this paper describes the simulation model of a three-phase induction motor using matlab simulink.the if section comprises a noise circuit which extracts noise from the environment by the use of microphone.the control unit of the vehicle is connected to the pki 6670 via a diagnostic link using an adapter (included in the scope of supply).47µf30pf trimmer capacitorledcoils 3 turn 24 awg,this project shows the controlling of bldc motor using a microcontroller.depending on the already available security systems,presence of buildings and landscape.here is the project showing radar that can detect the range of an object,90 % of all systems available on the market to perform this on your own.usually by creating some form of interference at the same frequency ranges that cell phones use,depending on the vehicle manufacturer,here a single phase pwm inverter is proposed using 8051 microcontrollers,the signal must be < – 80 db in the locationdimensions.the transponder key is read out by our system and subsequently it can be copied onto a key blank as often as you like,– active and passive receiving antennaoperating modes,from analysis of the frequency range via useful signal analysis.frequency band with 40 watts max.conversion of single phase to three phase supply,230 vusb connectiondimensions.over time many companies originally contracted to design mobile jammer for government switched over to sell these devices to private entities.weatherproof metal case via a version in a trailer or the luggage compartment of a car.when shall jamming take place.both outdoors and in car-park buildings,20 – 25 m (the signal must < -80 db in the location)size..
