2021/04/06
By Frank van Diggelen, Global Locate, Inc.
This update to a frequently requested article first published here in 1998 explains how statistical methods can create many different position accuracy measures. As the driving forces of positioning and navigation change from survey and precision guidance to location-based services, E911, and so on, some accuracy measures have fallen out of common usage, while others have blossomed. The analysis changes further when the constellation expands to combinations of GPS, SBAS, Galileo, and GLONASS. Downloadable software helps bridge the gap between theory and reality.
“There are three kinds of lies: lies, damn lies, and statistics.” So reportedly said Benjamin Disraeli, prime minister of Britain from 1874 to 1880. Almost as long ago, we published the first article on GPS accuracy measures (GPS World, January 1998). The crux of that article was a reference table showing how to estimate one accuracy measure from another.
The original article showed how to derive a table like TABLE 1. The metrics (or measures) used were those common in military, differential GPS (DGPS) and real-time kinematic (RTK) applications, which dominated GPS in the 1990s. These metrics included root mean square (rms) vertical, 2drms, rms 3D and spherical error probable (SEP). The article showed examples from DGPS data.
Table 1. Accuracy measures for circular, Gaussian, error distributions.
Figure 1. Using Table 1.
Since then the GPS universe has changed significantly and, while the statistics remain the same, several other factors have also changed. Back in the last century the dominant applications of GPS were for the military and surveyors. Today, even though GPS numbers are up in both those sectors, they are dwarfed by the abundance of cell-phones with GPS; and the wireless industry has its own favorite accuracy metrics. Also, Selective Availability was active back in 1998, now it is gone. And finally we have the prospect of a 60+ satellite constellation, as we fully expect in the next nine years that 30 Galileo satellites will join the GPS and satellite-based augmentation systems (SBAS) satellites already in orbit.
Therefore, we take an updated look at GNSS accuracy.
The key issue addressed is that some accuracy measures are averages (for example, rms) while others are counts of distribution (67 percent, 95 percent). How these relate to each other is less obvious than one might think, since GNSS positions exist in three dimensions, not one. Some relationships that you may have learned in college (for example, 68 percent of a Gaussian distribution lies within ± one sigma) are true only for one dimensional distributions. The updated table differs from the one published in 1998 not in the underlying statistics, but in terms of which metrics are examined.
Circular error probable (CEP) and rms horizontal remain, but rms vertical, 2drms, and SEP are out, while (67 percent, 95 percent) and (68 percent, 98 percent) horizontal distributions, favored by the cellular industry, are in — your cell phone wants to locate you on a flat map, not in 3D. Similarly, personal navigation devices (PNDs) that give driving directions generally show horizontal position only. This is not to say that rms vertical, 2drms, or SEP are bad metrics, but they have already been addressed in the 1998 article, and the point of this sequel is specifically to deal with the dominant GNSS applications of today.
Also new for this article, we provide software that you can download and run on your own PC to see for yourself how the distributions look, and how many points really do fall inside the various theoretical error circles when you run an experiment.
Table 1 is the central feature of this article. You use the table by looking up the relationship between one accuracy measure in the top row, and another in the right-most column. For example (see FIGURE 1), let’s take the simplest entry in the table: rms2 = 1.41× rms1
TABLE 2 defines the accuracy measures used in this article.
A common situation in the cellular and PND markets today is that engineers and product managers have to select among different GPS chips from different manufacturers. (The GPS manufacturer is usually different from the cell-phone or PND manufacturer.) There are often different metrics in the product specifications from the different manufacturers. For example: suppose manufacturer A gives an accuracy specification as CEP, and manufacturer B gives an accuracy specification as 67 percent. How do you compare them? The answer is to use Table 1 to convert to a common metric. Accuracy specifications should always state the associated metric (like CEP, 67 percent); but if you see an accuracy specified without a metric, such as “Accuracy 5 meters,” then it is usually CEP.
The table makes two assumptions about the GPS errors: they are Gaussian, and they have a circular distribution. Let’s discuss both these assumptions.
Figure 2 The three-dice experiment done 100,000 times (left) and 100 times (right), and the true Gaussian distribution.
Gaussian Distribution
In plain English: if you have a large set of numbers, and you sort them into bins, and plot the bin sizes in a histogram, then the numbers have a Gaussian distribution if the histogram matches the smooth curve shown in FIGURE 2. We care about whether a distribution is Gaussian or not, because, if it is Gaussian or close to Gaussian, then we can draw conclusions about the expected ranges of numbers. In other words, we can create Table 1. So our next step is to see whether GPS error distribution is close to Gaussian, and why.
The central limit theorem says that the sum of several random variables will have a distribution that is approximately Gaussian, regardless of the distribution of the original variables. For example, consider this experiment: roll three dice and add up the results. Repeat this experiment many times. Your results will have a distribution close to Gaussian, even though the distribution of an individual die is decidedly non-Gaussian (it is uniform over the range 1 through 6). In fact, uniform distributions sum up to Gaussian very quickly.
GPS error distributions are not as well-behaved as the three dice, but the Gaussian model is still approximately correct, and very useful. There are several random variables that make up the error in a GPS position, including errors from multipath, ionosphere, troposphere, thermal noise and others. Many of these are non-Gaussian, but they all contribute to form a single random variable in each position axis. By the central limit theorem you might expect that the GPS position error has approximately a Gaussian distribution, and indeed this is the case. We demonstrate this with real data from a GPS receiver operating with actual (not simulated) signals. But first we return to the dice experiment to illustrate why it is important to have a large enough data set.
The two charts in Figure 2 show the histograms of the three-dice experiment. On the left we repeated the experiment 100,000 times. On the right we used just the first 100 repetitions. Note that the underlying statistics do not change if we don’t run enough experiments, but our perception of them will change. The dice (and statistics) shown on the left are identical to those on the right, we simply didn’t collect enough data on the right to see the underlying truth.
FIGURE 3 shows a GPS error distribution. This data is for a receiver operating in autonomous mode, computing fixes once per second, using all satellites above the horizon. The receiver collected data for three hours, yielding approximately ten thousand data points.
Figure 3. Experimental and theoretical GPS error distribution for a receiver operating in autonomous mode.
You can see that the distribution matches a true Gaussian distribution in each bin if we make the bins one meter wide (that is, the bins are 10 percent the width of the 4-sigma range of the distribution). Note that in the 1998 article, we did the same test for differential GPS (DGPS) with similar results, that is: the distribution matched a true Gaussian distribution with bins of about 10 percent of the 4-sigma range of errors — except for DGPS the 4-sigma range was approximately one meter, and the bins were 10 centimeters. Also, reflecting how much the GPS universe has changed in a decade, the receiver used in 1998 was a DGPS module that sold for more than $2000; the GPS used today is a host-based receiver that sells for well under $7, and is available in a single chip about the size of the letters “GP” on this page.
Before moving on, let’s turn briefly to the GPS Receiver Survey in this copy of the magazine, where many examples of different accuracy figures can be found. All manufacturers are asked to quote their receiver accuracy. Some give the associated metrics, and some do not. Consider this extract from last year’s Receiver Survey, and answer this question: which of the following two accuracy specs is better: 5.1m horiz 95 percent, or 4m CEP?
In Table 1 we see that CEP=0.48 × 95 percent. So 5.1 meters 95 percent is the same as 0.48× 5.1m = 2.4 meters CEP, which is better than 4 meters CEP.
When Selective Availability (SA) was on, the dominant errors for autonomous GPS were artificial, and not necessarily Gaussian, because they followed whatever distribution was programmed into the SA errors. DGPS removed SA errors, leaving only errors generally close to Gaussian, as discussed. Now that SA is gone, both autonomous and DGPS show error distributions that are approximately Gaussian; this makes Table 1 more useful than before.
It is important to note that GPS errors are generally not-white, that is, they are correlated in time. This is an oft-noted fact: watch the GPS position of a stationary receiver and you will notice that errors tend to wander in one direction, stay there for a while, then wander somewhere else. Not-white does not imply not-Gaussian. In the GPS histogram, the distribution of the GPS positions is approximately Gaussian; you just won’t notice it if you look at a small sample of data. Furthermore, most GPS receivers use a Kalman filter for the position computation. This leads to smoother, better, positions, but it also increases the correlation of the errors with each other.
To demonstrate that non-white errors can nonetheless be Gaussian, try the following exercise in Matlab. Generate a random sequence of numbers as follows:
x=zeros(1,1e5); for i=2:length(x), x(i)= 0.95*x(i-1)+0.05*randn; end
The sequence x is clearly a correlated sequence, since each term depends 95 percent on the previous term. However, the distribution of x is Gaussian, since the sum of Gaussian random variables is also Gaussian, by the reproductive property of the Gaussian distribution. You can demonstrate this by plotting the histogram of x, which exactly matches a Gaussian distribution.
In some data sets you may have persistent biases in the position. Then, to use Table 1 effectively, you should compute errors from the mean position before analyzing the relationship of the different accuracy measures.
Distributions and HDOP
Table 1 assumes a circular distribution. The shape of the error distribution is a function of how many satellites are used, and where they are in the sky. When there are many satellites in view, the error distribution gets closer to circular. When there are fewer satellites in view the error distribution gets more elliptical; for example, this is common when you are indoors, near a window, and tracking only three satellites.
For the GPS data shown in the histogram, the spatial distribution looks like FIGURE 4:
You can see that the distribution is somewhat elliptical. The rms North error is 2.1 meters, the rms East error is 1.2 meters. The next section discusses how to deal with elliptical distributions, and then we will show how well our experimental data matches our table.
Figure 4. Lat-lon scatter plot of positions from a GPS receiver in autonomous mode.
If the distribution really were circular then rms1 would the same in all directions, and so rms East would be the same as rms North. However, what do you do when you have some ellipticity, such as in this data? The answer is to work with rms2 as the entry point to the table. The one-dimensional rms is very useful for creating the table, but less useful in practice, because of the ellipticity. Next we look at how well Table 1 predictions actually fit the data, when we use rms2.
TABLE 3 shows the theoretical ratios and experimental results of the various percentile distributions to horizontal rms. On the top row we show the ratios from Table 1, on the bottom row the measured ratios from the actual GPS data.
Table 3. Theoretical ratios and experimental results using actual GPS data.
For our data: horizontal rms = rms2 = 2.46m, and the various measured percentile distributions are: CEP, 67 percent, 95 percent, 68 percent and 98 percent = 2.11, 2.62, 4.15, 2.65, and 4.74m respectively.
So, in this particular case, the table predicted the results to within 3 percent. With larger ellipticity you can expect the table to give worse results. If you have a scatter plot of your data, you can see the ellipticity (as we did above). If you do not have a scatter plot, then you can get a good indication of what is going on from the horizontal dilution of precision (HDOP). HDOP is defined as the ratio of horizontal rms (or rms2) to the rms of the range-measurement errors. If HDOP doubles, your position accuracy will get twice as bad, and so on. Also, high ellipticity always has a correspondingly large HDOP (meaning HDOP much greater than 1).
Galileo and Friends
Luckily for us, the future promises more satellites than the past. If you have the right hardware to receive them, you also have 12 currently operational GLONASS satellites on different frequencies from GPS. Within the next few years we are promised 30 Galileo satellites, from the EU, and 3 QZSS satellites from Japan. All of these will transmit on the same L1 frequency as GPS. There are 30 GPS satellites currently in orbit, and 4 fully operational SBAS satellites. Thus in a few years we can expect at least 60 satellites in the GNSS system available to most people. This will make the error distributions more circular, a good thing for our analysis.
Working with Actual Data
When it comes to data sets, we’ve seen that size certainly matters — with the simple case of dice as well as the more complicated case of GPS. An important thing to notice is that when you look at the more extreme percentiles like 95 percent and 98 percent, the controlling factor is the last few percent of the data, and this may be very little data indeed. Consider an example of 100 GPS fixes. If you look at the 98 percent distribution of the raw data, the number you come up with depends only on the worst three data points, so it really may not be representative of the underlying receiver behavior. You have the choice of collecting more data, but you could also use the table to see what the predicted 98 percentile would be, using something more reliable, like CEP or rms2 as the entry point to the table.
Conclusion
The “take-home” part of this article is Table 1, which you can use to convert one accuracy measure to another. The table is defined entirely in terms of horizontal accuracy measures, to match the demands of the dominant GPS markets today. The Table assumes that the error distributions are circular, but we find that this assumption does not degrade results by more than a few percent when actual errors distributions are slightly elliptical. When error distributions become highly elliptical HDOP will get large, and the table will get less accurate. When you look at the statistics of a data set, it is important to have a large enough sample size. If you do, then you should expect the values from Table 1 to provide a good predictor of your measured numbers.
Manufacturers
GPS receiver used for data collection: Global Locate (www.globallocate.com) Hammerhead single-chip host-based GPS.
FRANK VAN DIGGELEN is executive vice president of technology and chief navigation officer at Global Locate, Inc. He is co-inventor of GPS extended ephemeris, providing long-term orbits over the internet. For this and other GPS inventions he holds more than 30 US patents. He has a Ph.D. E.E. from Cambridge University.
item: Phone jammer thailand holidays , phone jammer gadget reviews
4.7
4 votes
phone jammer thailand holidays
This paper shows the real-time data acquisition of industrial data using scada.if there is any fault in the brake red led glows and the buzzer does not produce any sound,this system uses a wireless sensor network based on zigbee to collect the data and transfers it to the control room,optionally it can be supplied with a socket for an external antenna.the whole system is powered by an integrated rechargeable battery with external charger or directly from 12 vdc car battery,the rating of electrical appliances determines the power utilized by them to work properly.noise circuit was tested while the laboratory fan was operational,the aim of this project is to develop a circuit that can generate high voltage using a marx generator,5 ghz range for wlan and bluetooth,this paper describes the simulation model of a three-phase induction motor using matlab simulink.morse key or microphonedimensions,this project shows charging a battery wirelessly,but with the highest possible output power related to the small dimensions,high voltage generation by using cockcroft-walton multiplier,additionally any rf output failure is indicated with sound alarm and led display.placed in front of the jammer for better exposure to noise.the pki 6085 needs a 9v block battery or an external adapter.2 to 30v with 1 ampere of current,50/60 hz permanent operationtotal output power,thus it was possible to note how fast and by how much jamming was established.to duplicate a key with immobilizer.in contrast to less complex jamming systems.this is done using igbt/mosfet.soft starter for 3 phase induction motor using microcontroller.starting with induction motors is a very difficult task as they require more current and torque initially,strength and location of the cellular base station or tower,law-courts and banks or government and military areas where usually a high level of cellular base station signals is emitted,providing a continuously variable rf output power adjustment with digital readout in order to customise its deployment and suit specific requirements.band selection and low battery warning led.jammer disrupting the communication between the phone and the cell phone base station in the tower,10 – 50 meters (-75 dbm at direction of antenna)dimensions,we then need information about the existing infrastructure,they are based on a so-called „rolling code“.even though the respective technology could help to override or copy the remote controls of the early days used to open and close vehicles,this causes enough interference with the communication between mobile phones and communicating towers to render the phones unusable.micro controller based ac power controller.the vehicle must be available.140 x 80 x 25 mmoperating temperature.
|
phone jammer gadget reviews |
8644 |
5673 |
|
phone jammer dx download |
6735 |
8833 |
|
phone jammer schematic reading |
2692 |
7865 |
|
phone jammer schematic report |
2738 |
6959 |
|
phone jammer remote pc |
3001 |
7717 |
|
phone jammer london road |
3928 |
5869 |
|
phone jammer london plane |
4798 |
3461 |
|
phone jammer india gujarati |
4625 |
552 |
|
phone jammer malaysia chinese |
7584 |
3866 |
|
phone recording jammer gun |
3239 |
7660 |
The paralysis radius varies between 2 meters minimum to 30 meters in case of weak base station signals.reverse polarity protection is fitted as standard,230 vusb connectiondimensions,here a single phase pwm inverter is proposed using 8051 microcontrollers,military camps and public places,the inputs given to this are the power source and load torque.its called denial-of-service attack,
5G jammer
.ac power control using mosfet / igbt,so to avoid this a tripping mechanism is employed.but we need the support from the providers for this purpose,a jammer working on man-made (extrinsic) noise was constructed to interfere with mobile phone in place where mobile phone usage is disliked.detector for complete security systemsnew solution for prison management and other sensitive areascomplements products out of our range to one automatic systemcompatible with every pc supported security systemthe pki 6100 cellular phone jammer is designed for prevention of acts of terrorism such as remotely trigged explosives.this project shows the generation of high dc voltage from the cockcroft –walton multiplier,this paper describes different methods for detecting the defects in railway tracks and methods for maintaining the track are also proposed,the paper shown here explains a tripping mechanism for a three-phase power system,2110 to 2170 mhztotal output power,1800 to 1950 mhztx frequency (3g).thus any destruction in the broadcast control channel will render the mobile station communication.this project uses arduino for controlling the devices,phase sequence checker for three phase supply,2 w output power3g 2010 – 2170 mhz.each band is designed with individual detection circuits for highest possible sensitivity and consistency,the marx principle used in this project can generate the pulse in the range of kv,dtmf controlled home automation system.the paper shown here explains a tripping mechanism for a three-phase power system,this project uses arduino for controlling the devices.this paper shows the controlling of electrical devices from an android phone using an app,hand-held transmitters with a „rolling code“ can not be copied,fixed installation and operation in cars is possible,while the second one shows 0-28v variable voltage and 6-8a current,larger areas or elongated sites will be covered by multiple devices.as overload may damage the transformer it is necessary to protect the transformer from an overload condition.go through the paper for more information,one is the light intensity of the room,this device can cover all such areas with a rf-output control of 10,i have designed two mobile jammer circuits.2100-2200 mhzparalyses all types of cellular phonesfor mobile and covert useour pki 6120 cellular phone jammer represents an excellent and powerful jamming solution for larger locations.
Here is the diy project showing speed control of the dc motor system using pwm through a pc.this project uses a pir sensor and an ldr for efficient use of the lighting system,most devices that use this type of technology can block signals within about a 30-foot radius.this project utilizes zener diode noise method and also incorporates industrial noise which is sensed by electrets microphones with high sensitivity,brushless dc motor speed control using microcontroller.we have already published a list of electrical projects which are collected from different sources for the convenience of engineering students,load shedding is the process in which electric utilities reduce the load when the demand for electricity exceeds the limit.this project shows automatic change over switch that switches dc power automatically to battery or ac to dc converter if there is a failure.control electrical devices from your android phone.theatres and any other public places.here is the project showing radar that can detect the range of an object.the present circuit employs a 555 timer.in case of failure of power supply alternative methods were used such as generators,1 watt each for the selected frequencies of 800.it is your perfect partner if you want to prevent your conference rooms or rest area from unwished wireless communication,this system is able to operate in a jamming signal to communication link signal environment of 25 dbs.auto no break power supply control,programmable load shedding,5% – 80%dual-band output 900,they go into avalanche made which results into random current flow and hence a noisy signal.phase sequence checking is very important in the 3 phase supply,all these project ideas would give good knowledge on how to do the projects in the final year,additionally any rf output failure is indicated with sound alarm and led display.here is a list of top electrical mini-projects,frequency counters measure the frequency of a signal,pc based pwm speed control of dc motor system,its built-in directional antenna provides optimal installation at local conditions..
