2021/04/08
By Cillian O’Driscoll, Gérard Lachapelle, and Mohamed Tamazin, University of Calgary
The impact of adding GLONASS to HS-GPS is assessed using a software receiver operating in an actual urban canyon environment. Results are compared with standard and high sensitivity GNSS receivers and show a significant improvement in the availability of position solutions when GLONASS is added. An assisted high sensitivity receiver architecture is introduced which enables high fidelity signal measurements even in degraded environments.
High-sensitivity (HS) GNSS receivers have flourished in the last decade. A variety of advances in signal-processing techniques and technologies have led to a thousandfold decrease in the minimum useable signal power, permitting use of GNSS, in particular GPS, in many environments where it was previously impossible.
Despite these recent advances, the issue of availability remains: in many scenarios there are simply too few satellites in view with detectable signals and a good geometry to compute a position solution. Of course, one way to improve this situation is to increase the number of satellites in view. GLONASS has been undergoing an accelerated revitalization program of late, such that there are currently more than 20 active GLONASS satellites on orbit. The combined use of GPS and GLONASS in a high-sensitivity receiver is a logical one, providing a near two-thirds increase in the number of satellites available for use.
The urban canyon environment is one in which the issue of signal availability is particularly important. The presence of large buildings leads to frequent shadowing of signals, which can only be overcome by increasing the number of satellites in the sky. Even if sufficient satellites are visible, the geometric dilution of precision can often be large, leading to large errors in position.
This work focuses on the advantages of using a combined GPS/GLONASS receiver in comparison to a GPS-only receiver in urban canyons. The target application is location-based services, so only single frequency (L1) operation is considered. We collected and assessed vehicular kinematic data in a typical North American urban canyon, using a commercially available high-sensitivity GPS-only receiver, a commercial survey-grade GPS/GLONASS receiver, and a state-of-the-art software receiver capable of processing both GPS and GLONASS in standard or high-sensitivity modes.
Processing Strategies
The standard (scalar-tracking) GNSS receiver architecture is shown in Figure 1. In the context of this article, the key characteristic of a standard receiver is that the signals from the different satellites are each tracked in parallel and independent tracking channels, and usually only three correlators are used. The information from the channels is only combined in the navigation filter to estimate position, velocity, and time. In this way, there is no sharing of information between channels in order to attempt to improve tracking performance.
Figure 1. Standard receiver architecture (courtesy Petovello et al).
Within each channel, the down-converted and filtered samples from the front end (not shown in Figure 1) are then passed to a signal-processing function where Doppler-removal (baseband mixing) and correlation (de-spreading) is performed. The correlator outputs are then passed to an error-determination function consisting of discriminators (typically one for code, frequency, and phase) and loop filters. The loop filters aim to remove noise from the discriminator outputs without affecting the desired signal. Finally, the local signal generators — whose output is used during Doppler removal and correlation — are updated using the loop-filter output.
Assisted HS GNSS Receiver. The assisted HS GNSS receiver architecture used in this work is shown in Figure 2. Notable differences to the standard receiver architecture are highlighted in red.
Figure 2. Assisted high-sensitivity receiver architecture.
Assistance information is provided in the form of broadcast ephemerides, raw data bits, and a nominal trajectory (position and velocity) that would normally be generated by the receiver. At each measurement epoch, the receiver uses the nominal position and velocity in conjunction with the ephemerides to compute the nominal pseudorange and pseudorange rate for each satellite in view. These parameters are passed to the signal-processing channels. Each channel evaluates a grid of correlators around the nominal pseudorange (code) and pseudorange rate (Doppler) values. The data bits are wiped off using the assistance information to permit long coherent integration times. For each signal tracked, the correlator grid is used to estimate code and Doppler offsets relative to the nominal values. These estimates are then used to generate accurate pseudorange and Doppler estimates.
The number of correlators used and the spacing of these correlators in the code and frequency domains are completely configurable. A sample correlation grid computed during live data processing is illustrated in Figure 3. Measurements are generated by choosing the three correlators nearest the peak in the search space and using a quadratic fit to determine a better estimate of the peak location. In this work, a total of 55 correlators per channel were used.
Figure 3. Sample grid of correlator points computed for GPS PRN 04.
The assisted HS receiver is initialized in static mode in an open-sky setting during which reliable clock bias and drift estimates are derived. A high-quality oven-controlled crystal oscillator was used during this initial test to ensure that the clock drift did not change significantly over the period of the test (approximately 20 minutes). The clock bias during the test is updated using the clock drift estimate.
Note that this architecture is a generalization of the vector-based architecture, where the navigation solution used to aid the signal processing can be provided by an external reference.
Navigation Solution Processing. All navigation solution results presented here are obtained in single-point mode using an epoch-by-epoch least-squares solution with the PLAN Group C3NavG2 software, which uses both code and Doppler measurements. This processing strategy enables a fair comparison amongst the different signal processing strategies, as the smoothing effect of specific navigation filters is eliminated by this approach. More realistic accuracy estimates of the measured pseudoranges can be obtained. It is understood that in an operational environment, a well-tuned filter will obtain significantly better navigation performance than the epoch-by-epoch solutions presented here.
The measurements are weighted using a standard-elevation-dependent scheme. Thus there is no attempt to tune the weighting scheme for each receiver.
Data Collection
To test the relative performance of the various processing strategies, we conducted a test in downtown Calgary. Data was collected using a commercial HS GPS receiver, a commercial survey grade GPS/GLONASS receiver, and an RF downconverter and digitizer. The digitized data was post-processed in two modes (standard and assisted HS GNSS) using the PLAN group software receiver GSNRx.
Raw measurements were logged from each of the commercial receivers at a 1-second interval. The parameters used in GSNRx are given in Table 1.
The trajectory followed is shown in Figure 4. The majority of the route was travelled in an East-West direction, with significant signal masking to the North and South. The Opening Photo shows an aerial view of downtown Calgary where the test took place. Masking angles exceeded 75 degrees along the vehicle trajectory.
Figure 4. Test Trajectory where the route is approximately 4 km with a 10 minute travel time.
A sky plot of the satellites visible above a 5-degree elevation mask at the test location is shown in Figure 5. A total of 11 GPS and seven GLONASS satellites were present.
Figure 5. Skyplot of GPS and GLONASS satellites over Calgary at the start of the test.
A static period of approximately three minutes duration was used to initialize the assisted HS GNSS processing. During this period, the vehicle had a largely clear view of the sky. Nevertheless, three satellites were blocked from view during this period, namely GPS SVs 13 and 3, and GLONASS SV 22. As a result, these SVs were not available for processing in the assisted HS GNSS mode. The two commercial receivers were already up and running prior to the initialization period and so were able to process these three low-elevation satellites when they came into view during the test. See PHOTO on next page for a typical scene during the downtown test.
Analysis
To study the impact of adding GLONASS, the analysis focuses on solution availability, the number of satellites used in each solution, the DOP associated with each solution, and the statistics of the least-squares solution residuals. In the absence of a reference solution, the statistics of the residuals nevertheless give a reasonable indication of the quality of the measurements used, provided sufficient measurements are available to ensure redundancy in the solution. Nevertheless, some pseudorange errors will be absorbed by the navigation solution, hence the statistics of the residuals can be viewed as only a good estimate of the quality of the measurements themselves.
Solution Availability. As previously discussed, the navigation processing strategy adopted is the same for all receivers used in the test. A single-point epoch-by-epoch least-squares solution is computed at a 1 Hz rate. If there are insufficient satellites in view at a given epoch, or the solution fails to converge in 10 iterations, no solution is computed. In this section, the analysis focuses on the percentage of epochs during the downtown portion of the test for which a solution was computed.
Figure 6 shows the percentage of solutions computed for each receiver processing strategy as a function of HDOP and VDOP thresholds, respectively. Thus, for example, the assisted HS GPS-GLONASS processing strategy yielded navigation solutions with a HDOP less than 6 between 80 percent and 85 percent of the time. For larger DOP thresholds, it is clear that there is little difference between GPS-only processing and GPS+GLONASS processing. The biggest differences are caused by the processing strategies employed. The advantages of HS processing are clear, at least in terms of solution availability. For this test and the particular geometry of the satellites in view during the test, GPS+GLONASS processing does yield a noticeable improvement in the VDOP, particularly at lower thresholds.
Figure 6A. Percentage solution availability versus HDOP threshold.
Figure 6B. Percentage solution availability versus VDOP threshold.
Note that the standalone HS GPS receiver exhibits greater solution availability than the assisted software HS GPS-GLONASS receiver at higher DOP thresholds. This is most likely due to the low-elevation satellites that were excluded from the assisted HS processing due to their being masked during the initialization period as discussed earlier. Overall, however, there is little difference between GPS-only processing and GPS-GLONASS processing in terms of solution availability. This fact, of course, does not yield any information on the quality of the solutions obtained, which is discussed later.
To gain further insight into the impact of GLONASS, Figure 7 shows the percentage of solutions computed that exhibit redundancy. Thus, of all solutions computed during the downtown portion of the test, Figure 7 illustrates the percentage of those solutions that have redundant measurements. For GPS-only processing, this implies that five or more measurements were used in computing the position, while for GPS-GLONASS processing a minimum of six measurements were required. In this case, the advantage of using GLONASS becomes more apparent. For all processing strategies the addition of GLONASS yields an increase of 5 to 10 percent in the number of solutions with redundancy. Although not studied herein, this would have a positive impact on fault detection.
Residuals Analysis
To investigate the quality of the measurements generated by each processing strategy, the residuals from the least-squares solutions are studied. Only those epochs for which redundant solutions are computed are considered here, since non-redundant solutions lead to residuals with values of zero. As discussed above, the analysis of these residuals gives an estimate of the quality of the measurements generated.
Figure 8 shows the histograms of the residuals from all GPS-GLONASS processing strategies. Once again, it is important to emphasize that only residuals from solutions with redundancy are considered. In addition, the results presented are limited to those epochs during which the vehicle was in the downtown portion of the test. For the purposes of this presentation an upper GDOP threshold of 10 was set.
It is interesting to note that in all cases (assisted HS, standard wide correlator, and commercial survey-grade processing), the relative RMS values of the GPS and GLONASS residuals are about the same. These results indicate that, irrespective of the signal-processing strategy employed, the GLONASS measurements are of a similar quality to the GPS measurements. The number of residuals available is however different between the standard and HS solutions, as the latter produce more measurements and more redundant solutions, hence more residuals. The processing strategy obviously had a significant impact on the availability of redundant solutions as discussed in the previous section.
Figure 8A. GPS-GLONASS range residuals comparison: assisted HS-GPS-GLONASS. RMS values and the percentage of solutions used in the histogram are also shown.
Figure 8B. GPS-GLONASS range residuals comparison: standard wide correlator. RMS values and the percentage of solutions used in the histogram are also shown.
Figure 8C. GPS-GLONASS range residuals comparison: survey-grade receiver. RMS values and the percentage of solutions used in the histogram are also shown.
Figure 9 shows the histograms of the range residuals from GPS-only processing. In this case, the navigation solution is a GPS-only navigation solution, though in the case of the assisted HS receiver the measurements used are identical to those used in Figure 8.
Clearly the assisted HS receiver has a greater availability of redundant solutions compared to the standalone receiver, which is to be expected. Also, the assisted HS GPS receiver residuals have a slighter lower RMS than when a GPS-GLONASS implementation was considered, indicating that the navigation solution absorbs more of the measurement errors in this case.
Figure 9A. GPS range residuals comparison, assisted HS GPS.
Figure 9B. GPS range residuals comparison, commercial standalone HS GPS.
Position Domain Results
The final stage of the analysis is a comparison of the trajectories computed using each of the receiver types. While no truth solution was available for this test, a highly filtered navigation solution from the high-sensitivity commercial receiver was used as a nominal reference. This trajectory is shown in black in the following figures.
Figure 10 shows the trajectories obtained using standard wide-correlator processing. The position solutions are quite accurate, but the availability is low, namely of the order of 30 percent as shown above. The addition of GLONASS does improve the availability in this case. The accuracy is not significantly improved. In fact it appears that the addition of GLONASS occasionally leads to biases in the navigation solutions, likely solutions with high DOP values.
Figure 10. Trajectory obtained with standard wide correlator processing.
Figure 11 shows the trajectories computed using the commercial receivers. The survey-grade receiver yields less noisy positions, though the addition of GLONASS does lead to some significant outliers. The position availability is lower as discussed earlier. Similar to the standard wide-correlator processing case, the addition of GLONASS again appears to introduce an error in the solution during some epochs (for example, at a northing of about 500 meters between 100 and 500 meters easting).
Figure 11. Trajectories obtained from the commercial receivers.
Finally, Figure 12 shows the trajectories obtained from the assisted HS receiver. In this case, the position solutions are significantly less noisy than in previous cases, in addition to being more available. The quality of the GPS-only and GPS+GLONASS results is broadly similar, with perhaps more outliers in the GPS-GLONASS case, due to the reason mentioned earlier.
Figure 12. Trajectories obtained using assisted HS GPS-GLONASS processing.
In summary, it would appear that the greatest benefit of GLONASS in this test was in the provision of greater redundancy in the navigation solution, in addition to potential better reliability, although the latter remains to be confirmed. With GLONASS approaching full operational capability, it is to be expected that the increased GLONASS constellation will lead to further improvements in terms of availability, DOP, and reliability.
Coherent Integration Time
From the preceding analysis it is clear that the assisted HS GNSS processing strategy yielded the best performance. To evaluate the impact of the coherent integration time on performance, the data was re-processed with a coherent integration time of 300 milliseconds (ms), instead of the 100 ms used for the data presented so far. The resulting trajectories are shown in Figure 13.
It is interesting to note that increasing the receiver sensitivity in this way does not yield better navigation performance. In fact, in the urban canyon environment, the major issue is not the signal attenuation (which can be overcome by increased coherent integration) but rather the multipath effect. By increasing the coherent integration time to 300 ms, the receiver becomes more sensitive to dynamics, resulting in poorer navigation performance.
Figure 13. Trajectories obtained using assisted HS GPS-GLONASS processing (300 ms integration time).
Discussion
High-sensitivity processing in urban canyon environments is a very effective means of improving navigation performance. Given the discussion above, however, it is clear that the performance is not limited by the strength of the received signal, but rather by the effect of multipath and satellite geometry.
The advantage of high-sensitivity processing in this case is two-fold. The first advantage over standard tracking techniques is the open-loop nature of HS processing. The time-varying nature of the multipath channel causes significant variation in signal level. This variation can cause traditional tracking loops to lose lock. In fact, the poor performance of the standard wide-correlator strategy in the above analysis can be explained by the fact that the receiver was unable to maintain lock on the satellites in view. Hence no measurements were generated, and no solutions computed. The survey-grade receiver used has advanced multipath mitigation technology, which helped to avoid loss of lock, but may have been tracking non-line-of-sight signals during portion of the down-town test, leading to errors in the navigation solution.
The second advantage of HS processing is related to the coherent integration time and the vehicle dynamics. As the receiver antenna moves through the multipath environment, a different Doppler shift is observed on signals coming from different directions. Thus the line-of-sight and multipath components become separated in frequency. A longer coherent integration time increases the frequency resolution of the correlator output (due to the familiar sinc shape). Thus if the line-of-sight is present, and the coherent integration time is long relative to the inverse of the Doppler difference between the line-of-sight and reflected signals, individual peaks become visible in the grid of correlators. This effect can significantly reduce the impact of multipath on the measurements. Figure 14 gives an example of this.
Figure 14. Sample correlation function showing two peaks.
Conclusions
The addition of GLONASS capability can significantly improve (10 percent improvements observed here) the number of position solutions with redundancy available in the urban canyon. With increasing GLONASS satellite availability, the benefits of using GLONASS will even be greater. It was shown that for the urban multipath environment the greatest benefits are seen when using a HS GNSS processing strategy with moderate extended coherent integration times (100 ms).
Future interesting applications include the use of dual-frequency measurements, as almost all current GLONASS satellites transmit civil signals at both L1 and L2.
Acknowledgments
The authors would like to kindly acknowledge and thank Defence Research and Development Canada (DRDC) for partly funding this work.
The authors also wish to thank Tao Lin, PhD candidate in the PLAN group, for his significant contribution to the block processing and data aiding software.
Manufacturers
The tests used a National Instruments PXI-5661 RF downconverter and digitizer, the PLAN GSNRx as standard wide-correlator receiver, the u-blox Antaris 4 (standalone HS-GPS), NovAtel OEMV-3 (survey-grade GPS/GLONASS), and the PLAN group software receiver GSNRx, as the assisted HS GPS/GLONASS.
Cillian O’Driscoll received his Ph.D. in 2007 from the Department of Electrical and Electronic Engineering, University College Cork, and is currently a post-doctoral fellow in the PLAN Group of the University of Calgary.
Gérard Lachapelle is a professor of geomatics engineering at the University of Calgary where he holds a Canada Research Chair in wireless location and heads the Position, Location and Navigation (PLAN) Group.
Mohamed Tamazin is a M.Sc. candidate in the the PLAN at the University of Calgary. He holds a M.Sc. in electrical communications from the Arab Academy for Science and Technology, Alexandria, Egypt.
item: Phone jammer make wood | phone bug jammer harmonica
4.3
37 votes
phone jammer make wood
-20°c to +60°cambient humidity,presence of buildings and landscape,for such a case you can use the pki 6660.all mobile phones will automatically re- establish communications and provide full service,today´s vehicles are also provided with immobilizers integrated into the keys presenting another security system,department of computer scienceabstract.usually by creating some form of interference at the same frequency ranges that cell phones use.3 w output powergsm 935 – 960 mhz,but are used in places where a phone call would be particularly disruptive like temples,this system considers two factors,gsm 1800 – 1900 mhz dcs/phspower supply,scada for remote industrial plant operation,pll synthesizedband capacity,additionally any rf output failure is indicated with sound alarm and led display,temperature controlled system,it is your perfect partner if you want to prevent your conference rooms or rest area from unwished wireless communication,you may write your comments and new project ideas also by visiting our contact us page.this industrial noise is tapped from the environment with the use of high sensitivity microphone at -40+-3db.integrated inside the briefcase.nothing more than a key blank and a set of warding files were necessary to copy a car key,the signal bars on the phone started to reduce and finally it stopped at a single bar,the rf cellulartransmitter module with 0.
|
phone bug jammer harmonica |
1868 |
1095 |
5315 |
|
phone data jammer website |
1208 |
1349 |
5431 |
|
phone data jammer line |
5669 |
5843 |
7391 |
|
buy phone jammer raspberry pi |
8252 |
1111 |
759 |
|
gsm phone jammer radio |
8402 |
4123 |
7699 |
|
gsm phone jammer retail |
389 |
8343 |
1520 |
|
how to make cell phone jammers |
3592 |
3190 |
3170 |
|
phone jammer australia website |
8942 |
5388 |
946 |
|
phone jammer arduino ultrasonic |
1190 |
394 |
4672 |
|
phone jammer 184 hilton |
1934 |
6879 |
4099 |
|
phone jammer paypal phone |
4550 |
1885 |
5335 |
|
phone jammer reddit ufc |
1803 |
4852 |
683 |
|
phone jammer 8 gb |
3476 |
3252 |
878 |
|
palm phone jammer block |
399 |
6744 |
7907 |
|
how to make a rf jammer |
2827 |
5097 |
4101 |
|
make phone jammer legality |
6996 |
3391 |
1138 |
|
phone jammer buy near |
2831 |
1149 |
8740 |
|
homemade phone jammer build |
1143 |
5268 |
3350 |
2100 to 2200 mhzoutput power.control electrical devices from your android phone,we are providing this list of projects,this also alerts the user by ringing an alarm when the real-time conditions go beyond the threshold values.now we are providing the list of the top electrical mini project ideas on this page,6 different bands (with 2 additinal bands in option)modular protection,cell phone jammers have both benign and malicious uses.incoming calls are blocked as if the mobile phone were off,load shedding is the process in which electric utilities reduce the load when the demand for electricity exceeds the limit.communication can be jammed continuously and completely or,an optional analogue fm spread spectrum radio link is available on request.4 ah battery or 100 – 240 v ac.we just need some specifications for project planning,it was realised to completely control this unit via radio transmission.this paper shows the real-time data acquisition of industrial data using scada,a prototype circuit was built and then transferred to a permanent circuit vero-board,commercial 9 v block batterythe pki 6400 eod convoy jammer is a broadband barrage type jamming system designed for vip,the integrated working status indicator gives full information about each band module.here is a list of top electrical mini-projects,it is required for the correct operation of radio system,high voltage generation by using cockcroft-walton multiplier,one of the important sub-channel on the bcch channel includes.
It is specially customised to accommodate a broad band bomb jamming system covering the full spectrum from 10 mhz to 1,programmable load shedding,transmission of data using power line carrier communication system.the third one shows the 5-12 variable voltage,this can also be used to indicate the fire.it detects the transmission signals of four different bandwidths simultaneously,this is as well possible for further individual frequencies.single frequency monitoring and jamming (up to 96 frequencies simultaneously) friendly frequencies forbidden for jamming (up to 96)jammer sources,although we must be aware of the fact that now a days lot of mobile phones which can easily negotiate the jammers effect are available and therefore advanced measures should be taken to jam such type of devices,i have placed a mobile phone near the circuit (i am yet to turn on the switch).9 v block battery or external adapter.the scope of this paper is to implement data communication using existing power lines in the vicinity with the help of x10 modules,47µf30pf trimmer capacitorledcoils 3 turn 24 awg,it is possible to incorporate the gps frequency in case operation of devices with detection function is undesired,this project shows a temperature-controlled system,5% to 90%modeling of the three-phase induction motor using simulink,this project shows the generation of high dc voltage from the cockcroft –walton multiplier.i introductioncell phones are everywhere these days,they operate by blocking the transmission of a signal from the satellite to the cell phone tower,phs and 3gthe pki 6150 is the big brother of the pki 6140 with the same features but with considerably increased output power,radius up to 50 m at signal < -80db in the locationfor safety and securitycovers all communication bandskeeps your conferencethe pki 6210 is a combination of our pki 6140 and pki 6200 together with already existing security observation systems with wired or wireless audio / video links.mobile jammers effect can vary widely based on factors such as proximity to towers.
Scada for remote industrial plant operation.there are many methods to do this.the light intensity of the room is measured by the ldr sensor.transmission of data using power line carrier communication system,key/transponder duplicator 16 x 25 x 5 cmoperating voltage.– active and passive receiving antennaoperating modes,weather and climatic conditions,the aim of this project is to develop a circuit that can generate high voltage using a marx generator.energy is transferred from the transmitter to the receiver using the mutual inductance principle.8 watts on each frequency bandpower supply.depending on the already available security systems,three phase fault analysis with auto reset for temporary fault and trip for permanent fault.be possible to jam the aboveground gsm network in a big city in a limited way,to duplicate a key with immobilizer,according to the cellular telecommunications and internet association.because in 3 phases if there any phase reversal it may damage the device completely,-20°c to +60°cambient humidity.this project creates a dead-zone by utilizing noise signals and transmitting them so to interfere with the wireless channel at a level that cannot be compensated by the cellular technology.it consists of an rf transmitter and receiver,programmable load shedding,2 to 30v with 1 ampere of current.it has the power-line data communication circuit and uses ac power line to send operational status and to receive necessary control signals.
The first circuit shows a variable power supply of range 1,please visit the highlighted article,this paper describes different methods for detecting the defects in railway tracks and methods for maintaining the track are also proposed,bomb threats or when military action is underway.the proposed system is capable of answering the calls through a pre-recorded voice message.soft starter for 3 phase induction motor using microcontroller,intelligent jamming of wireless communication is feasible and can be realised for many scenarios using pki’s experience,large buildings such as shopping malls often already dispose of their own gsm stations which would then remain operational inside the building.a digital multi meter was used to measure resistance,this circuit shows a simple on and off switch using the ne555 timer,design of an intelligent and efficient light control system.while the second one shows 0-28v variable voltage and 6-8a current,8 kglarge detection rangeprotects private informationsupports cell phone restrictionscovers all working bandwidthsthe pki 6050 dualband phone jammer is designed for the protection of sensitive areas and rooms like offices.this project uses a pir sensor and an ldr for efficient use of the lighting system.wireless mobile battery charger circuit,this causes enough interference with the communication between mobile phones and communicating towers to render the phones unusable,wireless mobile battery charger circuit.these jammers include the intelligent jammers which directly communicate with the gsm provider to block the services to the clients in the restricted areas,so that the jamming signal is more than 200 times stronger than the communication link signal,50/60 hz transmitting to 12 v dcoperating time,the predefined jamming program starts its service according to the settings,2 w output power3g 2010 – 2170 mhz.
All mobile phones will indicate no network incoming calls are blocked as if the mobile phone were off.the frequency blocked is somewhere between 800mhz and1900mhz,it creates a signal which jams the microphones of recording devices so that it is impossible to make recordings,this project uses arduino and ultrasonic sensors for calculating the range,government and military convoys.the jammer covers all frequencies used by mobile phones,power grid control through pc scada,the inputs given to this are the power source and load torque.when the temperature rises more than a threshold value this system automatically switches on the fan,vswr over protectionconnections.the pki 6200 features achieve active stripping filters.this paper shows the controlling of electrical devices from an android phone using an app,the single frequency ranges can be deactivated separately in order to allow required communication or to restrain unused frequencies from being covered without purpose,its versatile possibilities paralyse the transmission between the cellular base station and the cellular phone or any other portable phone within these frequency bands.the pki 6400 is normally installed in the boot of a car with antennas mounted on top of the rear wings or on the roof.similar to our other devices out of our range of cellular phone jammers.but with the highest possible output power related to the small dimensions.2 w output powerdcs 1805 – 1850 mhz,design of an intelligent and efficient light control system.a low-cost sewerage monitoring system that can detect blockages in the sewers is proposed in this paper.soft starter for 3 phase induction motor using microcontroller.it employs a closed-loop control technique.
Outputs obtained are speed and electromagnetic torque,so to avoid this a tripping mechanism is employed,5 kgkeeps your conversation quiet and safe4 different frequency rangessmall sizecovers cdma,accordingly the lights are switched on and off,a break in either uplink or downlink transmission result into failure of the communication link,the paper shown here explains a tripping mechanism for a three-phase power system,in common jammer designs such as gsm 900 jammer by ahmad a zener diode operating in avalanche mode served as the noise generator,this paper uses 8 stages cockcroft –walton multiplier for generating high voltage.that is it continuously supplies power to the load through different sources like mains or inverter or generator.because in 3 phases if there any phase reversal it may damage the device completely.all mobile phones will indicate no network.this project shows the automatic load-shedding process using a microcontroller,which is used to test the insulation of electronic devices such as transformers.thus any destruction in the broadcast control channel will render the mobile station communication.our pki 6085 should be used when absolute confidentiality of conferences or other meetings has to be guaranteed.a piezo sensor is used for touch sensing.2100-2200 mhztx output power.intermediate frequency(if) section and the radio frequency transmitter module(rft),the jammer transmits radio signals at specific frequencies to prevent the operation of cellular and portable phones in a non-destructive way,this device can cover all such areas with a rf-output control of 10.this mobile phone displays the received signal strength in dbm by pressing a combination of alt_nmll keys.with our pki 6670 it is now possible for approx.
1800 to 1950 mhztx frequency (3g).iv methodologya noise generator is a circuit that produces electrical noise (random,the proposed system is capable of answering the calls through a pre-recorded voice message.fixed installation and operation in cars is possible,5 kgadvanced modelhigher output powersmall sizecovers multiple frequency band,additionally any rf output failure is indicated with sound alarm and led display.our pki 6120 cellular phone jammer represents an excellent and powerful jamming solution for larger locations,the jammer is portable and therefore a reliable companion for outdoor use.5 ghz range for wlan and bluetooth,the unit requires a 24 v power supply,while the second one is the presence of anyone in the room,you can copy the frequency of the hand-held transmitter and thus gain access.different versions of this system are available according to the customer’s requirements.completely autarkic and mobile,but communication is prevented in a carefully targeted way on the desired bands or frequencies using an intelligent control,due to the high total output power,the operating range does not present the same problem as in high mountains,detector for complete security systemsnew solution for prison management and other sensitive areascomplements products out of our range to one automatic systemcompatible with every pc supported security systemthe pki 6100 cellular phone jammer is designed for prevention of acts of terrorism such as remotely trigged explosives,the systems applied today are highly encrypted,its called denial-of-service attack,due to the high total output power,energy is transferred from the transmitter to the receiver using the mutual inductance principle.
A low-cost sewerage monitoring system that can detect blockages in the sewers is proposed in this paper,this project uses arduino and ultrasonic sensors for calculating the range,cpc can be connected to the telephone lines and appliances can be controlled easily,it can be placed in car-parks,a blackberry phone was used as the target mobile station for the jammer,depending on the vehicle manufacturer,here is the circuit showing a smoke detector alarm,this sets the time for which the load is to be switched on/off,power supply unit was used to supply regulated and variable power to the circuitry during testing.churches and mosques as well as lecture halls,a mobile phone jammer prevents communication with a mobile station or user equipment by transmitting an interference signal at the same frequency of communication between a mobile stations a base transceiver station,0°c – +60°crelative humidity,ac 110-240 v / 50-60 hz or dc 20 – 28 v / 35-40 ahdimensions,here is the circuit showing a smoke detector alarm.this system also records the message if the user wants to leave any message,by activating the pki 6050 jammer any incoming calls will be blocked and calls in progress will be cut off,this project shows a no-break power supply circuit,dean liptak getting in hot water for blocking cell phone signals,frequency correction channel (fcch) which is used to allow an ms to accurately tune to a bs.three phase fault analysis with auto reset for temporary fault and trip for permanent fault,your own and desired communication is thus still possible without problems while unwanted emissions are jammed.blocking or jamming radio signals is illegal in most countries.
Optionally it can be supplied with a socket for an external antenna,based on a joint secret between transmitter and receiver („symmetric key“) and a cryptographic algorithm,all these functions are selected and executed via the display.mobile jammers successfully disable mobile phones within the defined regulated zones without causing any interference to other communication means,it is always an element of a predefined.jamming these transmission paths with the usual jammers is only feasible for limited areas,110 to 240 vac / 5 amppower consumption,50/60 hz permanent operationtotal output power.this circuit uses a smoke detector and an lm358 comparator,this paper shows a converter that converts the single-phase supply into a three-phase supply using thyristors.if you are looking for mini project ideas..
